Quoizel ER1814BN Emery User Manual
Page 2
2of2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at
2014 QuoizelInc.
March2014
A
AA
Hex Nut and
Lock Washer
Mounting Screw
Mounting Ball
mounting screws in or out of the
crossbar until the correct length
is achieved. Once the Ceiling
Canopy (A) is secure, remove the
mounting ball and Ceiling Canopy
(A) and proceed to Step 4.
Figure 3
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 - Install Fixture Body
A. Carefully tuck all wires into the outlet box
and position the Ceiling Canopy (A) over
the outlet box. Align the holes in the
Ceiling Canopy (A) with the mounting
screws, then attach the Ceiling Canopy
(A) using the previously removed
mounting balls. Hand tighten until snug.
A
AA
Mounting
Screw
Mounting
Ball
Figure 5
Figure 6
F
G
H
E
Socket
STEP 6
Install Shade
-
A. Place the Upper Collar (E), the Shade (F) and
the Steel Collar (G) in turn and secure with
the Harp with Socket Collar (H). Hand tighten
until snug.
Figure 7
STEP 7
Install Bulb
-
A. This fixture uses standard bulb with medium
base. Maximum 100 watts.
B. Insert bulb and screw snugly into place.
Bulb
STEP 8
Install Diffuser
-
A. Thread one Hex Nut (L) to the Nipple (I)
approx half way. Screw the Nipple (I)
into the bottom end of the Harp (H) and
tighten until snug. By using pliers,
thread the Hex Nut (L) against the Harp
(H) and hand tighten until snug.
B. Thread another Hex Nut (L) onto the end
of the Nipple (I) and adjust it to proper
location for rest components. Attach the
Flat Washer (J), the Rubber Washer (K),
the Diffuser (M) and the Small Flat
Washer (N) over the Nipple (I) in turn.
Secure them with the Finial (O) and hand
tighten until snug.
Your fixture is now assembled and ready
to use. Enjoy!
Figure 8
H
I
L
L
J
K
M
N
O
4
3
ER1814BN
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
NO.
(1) 100W
Bulb
(Not Supplied)
Medium
Base
1
FINISH: BRUSHED NICKEL
2
G134DI
9006EXBN
M2127SH
DIFFUSER 11.5"D
ROD EXTENSION BRUSHED NICKEL 6"L X 0.5"D
METAL SHADE BRUSHED NICKEL 13.5"D
1
2
1
4
3
9012EXBN
ROD EXTENSION BRUSHED NICKEL 12
”L X 0.5"D
2
5
” Dia.
3.5
”
51.5
”
OVERALL HEIGHT
(2)6
” AND (2)12” RODS
INCLUDES
13.5
” Dia.
11.5
”
2
1