Quoizel TF2819VB Pomez - Manual

CROSSBAR
GREEN GROUND
SCREW
LOCK NUT A
with SHAKE PROOF
WASHER A
LOCK NUT B
with SHAKE PROOF
WASHER B
( ) 2 OUTLET BOX
SCREWS
NIPPLE
FIXTURE SUPPLY WIRE
and GROUND WIRE
CANOPY
CHAIN LOOP
CEILING
CANOPY
CANOPY
LOCK RING
FIXTURE CHAIN
FIXTURE LOOP
HOOK
FIXTURE CANOPY
CENTER
ASSEMBLY
( ) ,
(
)
4 SUPPORT RODS
or CHAINS Depends
on style purchased
SOCKET
CLUSTER
HOOK
STEM
SHADE
SHADE
LOOP
FINIAL
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
FIGURE1
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
ASSEMBLY INSTALLATION INSTRUCTIONS
/
IS 646
Revised 2006 5 13
-
- -
1 Before beginning the installation carefully unpack and
identify all parts referring to the illustration FIGURE1
2 Locate the CENTER ASSEMBLY and unravel FIXTURE
SUPPLY WIRE AND GROUND WIRE
3 Locate the CROSSBAR and with power to installation
point OFF secure to OUTLET BOX with 2 OUTLET
BOX SCREWS not supplied Locate LOCK NUT A
and SHAKE PROOF WASHER A Thread LOCK NUT
A and SHAKE PROOF WASHER A onto top end of
NIPPLE
Thread the NIPPLE into the center of the
CROSSBAR Locate LOCK NUT B and thread bottom
end of NIPPLE Tighten LOCK NUT A against
CROSSBAR with plier until snug
4 Locate the FIXTURE CHAIN and determine desired
hanging height of fixture Adjust chain by removing
links if needed Please note that depending on chain
material thickness you might be required to use chain
pliers to spread links open Proceed to attach one end
of chain to FIXTURE LOOP attach to the top of the
fixture Ureavel FIXTURE SUPPLY and GROUND
WIRE and pass through FIXTURE CHAIN alternating
links
Proceed to pass the fixture wires through the
following mounting components in this order
1 CANOPY LOCK RING
2 CEILING CANOPY
3 CANOPY CHAIN LOOP 4 SHAKE PROOF WASHER
B and LOCK NUT B 5 NIPPLE
6 LOCK NUT A and
SHAKE PROOF WASHER A
5
Position the fixture underneath the CEILING MOUNTED
OUTLET BOX
and pass SUPPLY WIRE and GROUND
WIRE through the center of NIPPLE Use wire
connectors not supplied Connect the HOUSE GROUND
WIRE to the FIXTURE GROUND WIRE
connect the
HOUSE WHITE or RIBBED SDIE WIRE to the
FIXTURE WHITE or RIBBED SIDE WIER connect the
HOUSE BLACK or RED WIRE to the FIXTURE BLACK
or SMOOTH SIDE WIER Make sure there are no
exposed wires and wrap each connection with approved
electrical tape
6 Carefully tuck in all wiring into the OUTLET BOX and
thread the CANOPY CHAIN LOOP onto the bottom of
NIPPLE
Thread LOCK NUT B and SHADE PROOF
WASHER B onto top of CANOPY CHAIN LOOP Tighten
with pliers locate the CEILING CANOPY over the
CEILING MOUNTED OUTLET BOX and secure against
ceiling by threading the CANOPY LOCK RING onto
the CANOPY CHAIN LOOP
Proceed to attach the top
of FIXTURE CHAIN to the CANOPY CHAIN LOOP
Carefully compress end of FIXTURE CHAIN to secure
7 Install bulbs referring to fixture markings and or labels
for maximum wattage
8 Locate STEM and thread into the bottom center of
SOCKET CLUSTER Hand tighten until snug
9 Locate the SHADE and position the MOUNTING HOLE
at the bottom of the SHADE over the STEM Pass
STEM through MOUNTING HOLE Proceed to attach
1 HOOK at end of SUPPORT ROD to 1 SHADE
LOOP inside of SHADE Repeat process for remaining
arms Please note that depending on style purchased
there might be SUPPORT ROD or CHAINS Locate
FINIAL and attach to end of STEM protruding from
SHADE
Tighten until snug
10 Attach tops of 4 SUPPORT RODS or CHAINS to
the 4 HOOKS on the side of FIXTURE CANOPY
11 Restore the power to the installation point ON Retain
this sheet for future reference
. ,
, ( ).
.
.
.
, ( )
( ).
.
.
.
.
.
.
.
.
,
.
,
.
.
:
) ; ) ;
) ; )
; ) ; )
.
.
,
.
( )
;
( )
( ) ;
( )
( ) .
.
.
.
.
.
.
.
.
. /
.
.
. .
.
.
.
( ) ( )
.
. ( ,
).
. .
. ( ) ( )
( ) .
. .
.
Make the wire connections (Quoizel recommends
2 people for next 3 steps
:
)