Triton MSA 200 User Manual

Page 3

Assembly / Warranty

ASSEMBLY

Fold the legs of the Main Body Assembly (A) fully

outwards. Loosen the round knob and extend

the stem upwards, then tighten.
Note: The legs should pivot firmly. Adjust the

nuts on the leg pivot bolts if necessary.
Fit the Saddles (B) to the stem using the locating

pins on the saddles as shown.
Attach the Front (C) and Rear (D) Quadrants

using the shorter Hex Bolt (E), Small Washers (F)

and Nyloc Nut (G). Do not over-tighten.
Fit the Quadrant Washer (I) onto the longer Hex

Bolt (J) with the hex head located in the tabs on

the washer. Insert the bolt through the slots in

the quadrants, ensuring that it passes through

the washer held within each quadrant and the

hole in the lower stem saddles. Fasten the Large

Washer (H) onto the bolt with the Round Knob

and M6 Nut (K).
Rotate the quadrants until the flat tops are

horizontal then gently nip up the round knob.
Fasten the Head Assembly (L) to the quadrants

using the Pan Head Bolts (M). The round knob

on the clamp which is built into the head should

be on the same side as the round knob on the

quadrant.
Adjust the nut tension on the Hex Bolt (E) if

necessary. The head should pivot firmly, and

should lock tightly at any selected angle when
the quadrant knob is tightened.

WARNINGS
• Make sure the legs are fully opened, and

that both the stem clamp and the quadrant

clamp are fully tightened before applying

heavy loads.
• Do not overload. Max. load per Multi-Stand

100kg (220lb).
• Do not stand on this product.
• When using the head clamp to clamp

materials less than 30mm, use a packing

piece.
• Clamp an extension piece (ie. an offcut of

sheet material - as shown on product

carton) into the head channel if using Multi-

Stand to support material at a height greater

than its maximum adjustment.
• When clamping easily damaged materials,

eg. doors, use thin packing on both sides to
avoid damage.
• Make sure the Multi-Stand is securely
pegged down to the ground when applying
non-vertical loads; or when on steeply
sloping ground.

Inhoud / Symbolen / Onderdelen

INHOUD

Hartelijk dank voor de aanschaf van dit Triton-gereedschap. Deze instructies geven informatie voor een veilige

en doeltreffende bediening van dit product.

Lees deze handleiding zodat u de voordelen van het unieke design van dit product ten volle kunt benutten. Houd

deze handleiding bij de hand en zorg ervoor dat alle gebruikers van dit gereedschap de handleiding hebben

gelezen en volledig hebben begrepen.

Symbolen

Onderdelen

Montage

Garantie

SYMBOLEN

Draag altijd gehoorbescherming, een

veiligheidsbril en een stofmasker

Waarschuwing

Zorg dat u de handleiding volledig hebt

doorgenomen en begrepen voor u dit

product gebruikt

Triton Precision Power Tools guarantees

to the purchaser of this product that if

any part proves to be defective due to

faulty materials or workmanship within

12 MONTHS from the date of original

purchase, Triton will repair, or at its

discretion replace, the faulty part free of

charge.
This guarantee does not apply to

commercial use nor does it extend to

normal wear and tear or damage as a

result of accident, abuse or misuse.
* Register online within 30 days.
Terms & conditions apply.
This does not affect your statutory rights

To register your guarantee visit our web site at

www.tritontools.com* and enter your details.
Your details will be included on our mailing list

(unless indicated otherwise) for information on

future releases. Details provided will not

be made available to any third party.

PURCHASE RECORD

Date of Purchase: ___ / ___ / ____
Model: MSA200

Retain your receipt as proof of purchase

WARRANTY

ONDERDELEN

A. Voorgemonteerde voetsteun (1)
B. Beugels (4)
C. Voorkwadrant (1)
D. Actherkwadrant (1)
E. Zeskantbout (M6 x 60 mm) (1)
F. Kleine borgring (2)
G. Borgmoer nylon ring (M6) (1)
H. Grote borgring (1)
I. Kwadrantborgring (1)
J. Zeskantbout (M6 x 80 mm) (1)
K. M6 moer ronde knop (1)
L. Kopstuk (1)
M. Cilinderkopbout (M6 x 10 mm) (4)