IDX ET-PV2BM User Manual
Et-pv2bm, V-mount adaptor for blackmagic cinema camera
ET-PV2BM
V-Mount Adaptor for Blackmagic Cinema Camera
Instruction Manual
Thank you for choosing the ET-PV2BM. Designed specifically for use with the Blackmagic
Cinema Camera, the ET-PV2BM attaches directly to the IDX A-CP(A) universal mounting plate,
or other 3
rd
party manufactured mounting plates. Please check which fixing positions are required
for 3
rd
party plates and use the appropriate location holes. The ET-PV2BM incorporates an
integral IDX V-Mount plate allowing direct mounting of any IDX ENDURA battery. To install,
simply connect the DC power output cable to the DC-IN connector of the camera.
The ET-PV2BM has a D-Tap DC-OUT connector that supplies power directly from the battery
allowing the use of professional on-board camera lights or other accessories. Please note, this is
an unregulated output.
Specifications
Dimensions: 82.5(w) x 142(h) x 12(d) mm
Weight: 210g approx.
Cable output voltage: 12~17V
D-Tap output voltage: 12~17V
Maximum output for D-Tap: 50W
Cable length: 1m approx.
Included accessories: M3 (8mm) screw x 4
General Notes & Safety
Do not attempt to open or modify this unit. All work should be carried out by IDX authorised
service personnel only.
Do not attach the ET-PV2BM to any non-compatible video camera or equipment as it may cause
defect, damage or other incidents. Please read this Instruction Manual carefully before use.
When connecting a battery or adaptor to the ET-PV2PM, be sure to connect firmly. If it is not
attached properly, it may result in loss or damage to the unit or even injury to the user.
Do not expose to, use or place the unit in direct sunlight, extreme dust or other hazardous
environments.
A short between the plus (+) and minus (-) charge pins may cause fire, electrical shock or other
incidents.
Stop using immediately in case of abnormal smell, leak, colour change or deformity during use.
If you need any inspection or repairs, please contact your local IDX dealer or IDX office.
IDX Technology Europe, Ltd.
Unit 9 Langley Park, Waterside Drive, Langley, Berkshire SL3 6EZ, ENGLAND
Tel: +44-1753-547692
Fax: +44-1753-546660
Email: [email protected]
www.idx-europe.co.uk
20121812
ET-PV2BM
V-Mount Adaptor for Blackmagic Cinema Camera
Instruction Manual
Thank you for choosing the ET-PV2BM. Designed specifically for use with the Blackmagic
Cinema Camera, the ET-PV2BM attaches directly to the IDX A-CP(A) universal mounting plate,
or other 3
rd
party manufactured mounting plates. Please check which fixing positions are required
for 3
rd
party plates and use the appropriate location holes. The ET-PV2BM incorporates an
integral IDX V-Mount plate allowing direct mounting of any IDX ENDURA battery. To install,
simply connect the DC power output cable to the DC-IN connector of the camera.
The ET-PV2BM has a D-Tap DC-OUT connector that supplies power directly from the battery
allowing the use of professional on-board camera lights or other accessories. Please note, this is
an unregulated output.
Specifications
Dimensions: 82.5(w) x 142(h) x 12(d) mm
Weight: 210g approx.
Cable output voltage: 12~17V
D-Tap output voltage: 12~17V
Maximum output for D-Tap: 50W
Cable length: 1m approx.
Included accessories: M3 (8mm) screw x 4
General Notes & Safety
Do not attempt to open or modify this unit. All work should be carried out by IDX authorised
service personnel only.
Do not attach the ET-PV2BM to any non-compatible video camera or equipment as it may cause
defect, damage or other incidents. Please read this Instruction Manual carefully before use.
When connecting a battery or adaptor to the ET-PV2PM, be sure to connect firmly. If it is not
attached properly, it may result in loss or damage to the unit or even injury to the user.
Do not expose to, use or place the unit in direct sunlight, extreme dust or other hazardous
environments.
A short between the plus (+) and minus (-) charge pins may cause fire, electrical shock or other
incidents.
Stop using immediately in case of abnormal smell, leak, colour change or deformity during use.
If you need any inspection or repairs, please contact your local IDX dealer or IDX office.
IDX Technology Europe, Ltd.
Unit 9 Langley Park, Waterside Drive, Langley, Berkshire SL3 6EZ, ENGLAND
Tel: +44-1753-547692
Fax: +44-1753-546660
Email: [email protected]
www.idx-europe.co.uk
20121812
E & OE
E & OE