Feed water guidelines, Specifications, Dimensions - weight – Watts CWS200 User Manual
Page 2: Ordering information
Feed Water Guidelines
pH . . . . . . . . . . . . . . . . . . . . . . . 6 to 10
Hardness (maximum) . . . . . . . . . Depends on customers acceptable
hardness leakage level.
Water Pressure . . . . . . . . . . . . . 25psi to 125psi (171 kPa to 8.5 bar)
Temperature . . . . . . . . . . . . . . . 34 - 110°F (1 - 43°C)
Free Chlorine (maximum) . . . . . . 1mg/L
Iron (maximum) . . . . . . . . . . . . . 1mg/L
Oil and H2S . . . . . . . . . . . . . . . . None Allowed
Turbidity . . . . . . . . . . . . . . . . . . Less than 5.0 NTU
For all other guideline information please contact your Watts represen-
tative.
Specifications
ES-WQ-CWS200 1306
© 2013 Watts
USA: Tel. (800) 659-8400 • www.watts.com
Canada: Tel. (888) 208-8927 • www.watts.ca
A Watts Water Technologies Company
Note: Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.
Dimensions - Weight
CWS200 SERIES
OVERALL
OVERALL
OVERALL
mOdEL
TANK
IN
OUT
HEIGHT
dEPTH
WIdTH
BRINE TANK
M4543W
14"X65"
68.3" 68.3" 74.2" 15.2" 17.7" 18"X40"
M4547W
16"X65"
68.0" 68.0" 73.6" 16.2" 18.5" 18"X40"
M4548W
18"X65"
70.5" 70.5" 76.1" 20.1" 20.5" 24"X41"
M4552W
21"X62"
70.4" 70.4" 76.0" 21.1" 21.1" 24"X50"
M4558W
24"X72"
77.5" 77.5" 83.1" 24.1" 24.1" 30"X50"
M4559W
30"X72"
77.5" 77.5" 83.1" 30.1" 30.1" 39"X48"
M4560W
36"X72"
87.3" 87.3" 92.8" 36.1" 36.1" 39"X48"
Note: This information is not intended to replace the product installation and safety information available or the experience of a trained prod-
uct installer. Please refer to the product installation and safety instructions for further information.
mINERAL TANK
BRINE TANK
SOfTENING
LBS. SALT PER
fLOW RATE & PRESSURE
TANK RESIN GRAVEL TANK
SALT
CAPACITY
REGENERATION
SERV
dROP
BKW
mOdEL
SIZE
ft
3
SIZE
fILL
mAx
mIN
mAx
mIN
GPm
PSI
GPm
M4543W
14x65
3
60 lbs.
18x40
400
90 K
60 K
45
18
39/50
15/25
5
M4547W
16x65
4
80 lbs.
18x40
400
120 K
80 K
60
24
47/60
15/25
7
M4548W
18x65
5
100 lbs.
24x41
600
150 K
100 K
75
30
53/69
15/25
10
M4552W
21x62
7
100 lbs.
24x50
600
210 K
140 K
105
42
66/85
15/25
13
M4558W
24x72
10
200 lbs.
30x50
1200
300 K
200 K
150
60
73/94
15/25
15
M4559W
30x72
15
400 lbs.
39x48
2200
450 K
300 K
225
90
84/109
15/25
25
M4560W
36x72
20
500 lbs.
39x48
2200
600 K
400 K
300
120
93/119
15/25
35
Note: Capacities are based on resin manufacturer’s data and are dependent upon influent water TDS, temperature, bed depth, and
flow rates. Feed water must be free of oil and color. Pipe size, tank size, and space requirements are in inches. Capacities and flow rates
expressed above are per tank. Flow rates listed at 25psi drops are for intermittent peak flow rates and are not to be used as continuous flows.
Note: Flow rates listed above are based on pressure drop only. Selecting a system based on pressure drop alone does not guarantee that
the system will proved adequately softened water. System selection should be based on resin quantity, capacity required, feed water analy-
sis, and application requirements.
Ordering Information
mOdEL
dESCRIPTION
SPACE REQUIREd
WEIGHT
LBS KGS
M4543W
A0090FM200WE with turbine meter
24 x 44 x 87
265
120
M4547W
A0120FM200WE with turbine meter
24 x 46 x 87
350
159
M4548W
A0150FM200WE with turbine meter
24 x 48 x 89
400
181
M4552W
A0210FM200WE with turbine meter
24 x 52 x 89
600
272
M4558W
A0300FM200WE with turbine meter
30 x 60 x 96
710
322
M4559W
A0450FM200WE with turbine meter
39 x 75 x 106
1160
526
M4560W
A0600FM200WE with turbine meter
39 x 81 x 107
1560
707