Bully Dog 40440 GT for Jeep Quick Guide - Manual (Page 2)

D
:
3.
Internet access
In the unlikely event
that technical support is
needed, Internet access
may be required to
troubleshoot.
4.
Allow enough time
Make sure you have
at least an hour
to complete the
installation process.
5.
Check your battery
Before installation,
ALWAYS ensure that
the batteries are fully
charged. If you are not
sure, connect a battery
charger before you
begin installation.
6.
Turn electronics OFF
Leaving electronics on
(stereo included) may
prevent a successful
download.
7.
The download
Do not interrupt or
disconnect the GT
at any point during
the download. Leave
electronics off during
the entire process.
Proceed to (
E ).
PRE-TUNE CHECKLIST
1.
Business hours
Install during regular
business hours (Monday-
Friday 8am-5pm MST). For
assistance, you may contact
Bully Dog Technical Support
at 940-783-9915 .
2.
Check fuses
Check the
included red fuse
card if you have a
GM vehicle.
GT DOWNLOAD (PART 2)
2012-2013 Wranglers only; for all other vehicles, skip to H-1.
1.
The GT will display code 262.
• Remove the microSD memory
card from the GT.
• Connect it to the computer
with the included card reader.
Steps 2-4 must be completed outside the
vehicle on a computer with Internet access.
2.
Open the Bully Dog Update Agent.
• http://www.bullydog.com/domains/updateagent/setup.exe
3.
Connect the microSD memory
card to the computer.
• Use the included
card reader and a
USB port on the
computer.
4.
The Update Agent will display a
progress bar as it gathers files.
• When the Update Agent displays
a message that the process is
complete, click OK.
F
:
GT DOWNLOAD (PART 4)
G
:
GT DOWNLOAD (PART 3)
2012-2013 Wranglers only; for all other vehicles, skip to H-1.
Steps 1-4 are must be
completed with/inside
the vehicle.
1.
Reinstall the microSD
memory card in the GT.
2.
Choose “Install Download” from the Main Menu.
4.
Read the battery disclaimer and press “Agree.”
3.
Read the disclaimer and press “Agree.”
E
:
GT DOWNLOAD (PART 1)
2.
Choose “Change Vehicle” from the Main Menu.
1.
Turn your key to the “on” (or “run”) position.
• Do NOT start the engine.
3.
Select the vehicle model,
engine and year.
• The GT will load files and
restart.
4.
Choose “Install Download” from the
Main Menu.
6.
Read the disclaimer and press “Agree.”
7.
Read the battery disclaimer and press “Agree.”
8.
The GT will retrieve vehicle data.
or
MAIN MENU Go Back
to General Disp
Change Vehicle
Install Download
Gauge Setup
Set User Options
MAIN MENU Go Back
to General Disp
Install Download
Gauge Setup
Set User Options
Performance Testing
TOP
To download this agreement
go to:
www.bullydog.cm/warranty.php
This is the final opportunity
to exit the download
procedure by pressing disagree.
AGREE
DISAGREE
BATTERY CONDITION
TOP Press CONTINUE if you are
satisfied with your battery
condition or connected a
battery charger or booster.
CONTINUE
CANCEL
VEHICLE DATA
Retrieving Vehicle Data
Please Wait. ...
5.
Verify the vehicle type.
CAUTION Go Back
to Main Menu
YES
Please verify vehicle type.
Installing on a
XXXXXXXXXXXXXXXXXX
If this is correct, press Y to continue.
If not, restart and select the correct
vehicle.
LOADING IMAGE 10
%
Selected:
XXXXXXXXXXXXXXXXXXX
Loading file from SD card.
2.
The GT will prompt you to select tuning features:
• Power Level
• Drive Rev. Limiter
• Neutral Rev. Limiter
• Speed Limiter
• MDS (if available) • Adjust WOT Shift Points
(if available, automatic
transmissions only)
• Tire Size
• Axle Ratio
3.
The GT will build and download the tuning file.
• Do not interrupt the GT.
5.
When the GT
has finished
installing the
tuning file, the
download is
complete!
• Slide the switch
on the adapter
plug to “KEY”
24 % BUILDING FILE
TUNE
Please Wait....
XXXXXXXXX
DOWNLOADING
TUNE
Part 2
Please Wait....
Do Not Unplug GT!
Please Press Continue
INITIAL DOWNLOAD
The Following Process
Takes Several Minutes
Continue
5.
The GT will begin the initial
download.
• This will take several minutes.
• Do not interrupt the GT.
• Follow the onscreen instructions.
6.
Once the GT has completed the
initial download, skip to step H-2.
1.
The GT will read the engine files.
- This will take several minutes.
- Do not interrupt the GT.
- Follow the onscreen instructions.
58 % READING
ENGINE
Please Wait....
Do Not Unplug the GT!
H
: