Baumfolder BaumCut 26.4 (For serials 69H1122 thru 76D1132) - Manual (Page 21)

K2 - 3
Observe all safety instructions and warnings attached to the
machine/plant.
See to it that safety instructions and warnings attached to
the machine are always complete and perfectly legible.
In the event of safety-relevant modifications or changes in
the behaviour of the machine/plant during operation, stop
the machine/plant immediately and report the malfunction
to the competent authority/person.
Never make any modifications, additions or conversions
which might affect safety without the supplier´s approval.
This also applies to the installation and adjustment of safety
devices and valves as well as to welding work on load-
bearing elements.
Spare parts must comply with then technical requirements
specified by the manufacturer. Spare parts from original
equipment manufacturers can be relied to do so.
Never modify the software of programmable control sy-
stems.
Replace hydraulic hoses within stipulated and appropriate
intervals even if no safety-relevant defects have been
detected.
Adhere to prescribed intervals or those specified in the
operating instructions for routine checks and inspections.
Selection and qualification of personnel - Basic respon-
sibilities
Any work on and with the machine/plant must be executed
by reliable personnel only. Statutory minimum age limits
must be observed.
Employ only trained or instructed staff and set out clearly
the individual responsibilities of the personnel for operation,
set-up, maintenance and repair.
Make sure that only authorized personnel works on or with
the machine.
Define the machine operator´s responsibilities - also with
regard to observing traffic regulations - giving the operator
the authority to refuse instructions by third parties that are
contrary to safety.
Do not allow persons to be trained or instructed or persons
taking part in a general training course to work on or with
the machine/plant without being permanently supervised by
an experienced person.
Work on the electrical system and equipment of the machi-
ne/plant must be carried out only by a skilled electrician or
by instructed persons under the supervision and guidance
of a skilled electrician and in accordance with electrical
engineering rules and regulations.
Work on the hydraulic system must be carried out only by
personnel with special knowledge and experience of
hydraulic equipment.
Safety instructions governing specific operational
phases
Standard operation
Avoid any operational mode that might prejudicial to safety.
Take the necessary precautions to ensure that the machine
is used only when in a safe and reliable state.
Operative machine only if all protective and safety-oriented
devices, such as removable safety devices, emergency
shut-off equipment, sound-proofing elements and exhau-
sters, are in place and fully functional.
Check the machine/plant at least once per working shift for
obvious damage and defects. Report any changes (incl.
changes in the machine´s working behaviour) to the
competent organization/person immediately. If necessary,
stop the machine immediately and lock it.
In the event of malfunctions, stop the machine/plant
immediately and lock it. Have any defects rectified imme-
diately.
During start-up and shut-down procedures always watch
the indicators in accordance with the operating instructions.
Before starting up or setting the machine/plant in motion,
make sure that nobody is at risk.
Never switch off or remove suction and ventilation devices
when the machine is in operation.
Special work in conjunction with utilization of the
machine/plant and maintenance and repairs during
operation; disposal of parts and consumables
Observe the adjusting , maintenance and inspection
activities and intervals set out in the operating instructions,
including information on the replacement of parts and
equipment. These activities may be executed by skilled
personnel only.
Brief operating personnel before beginning special operati-
ons and maintenance work, and appoint a person to
supervise the activities.
In any work concerning the operation, conversion or
adjustment of the machine and its safety-oriented devices
or any work related to maintenance, inspection and repair,
always observe the start-up and shut-down procedures set
out in the operating instructions and the information on
maintenance work.
Ensure that the maintenance area is adequately secured.
If the machine/plant is completely shut-down for mainte-
nance and repair work, it must be secured against inadver-
tent starting by:
-
locking the principal control elements and removing
the ignition key and/or
-
attaching a warning sign to the main switch.
Clean the machine, especially connections and threaded
unions, of any traces of oil or presevatives before carrying
out maintenance/repair. Never use aggressive detergents.
Use lint-free cleaning rags.
Always tighten any screwed connections that have been
loosened during maintenance and repair.
Any safety devices removed for set-up, maintenance or
repair purposes must be refitted and checked immediately
upon completion of the maintenance and repair work.
Ensure that all consumables and replaced parts are
disposed of safely and with minimum environmental
impact.