I-fold electrical installation – Baumfolder BAUM20: Ifold Service Manual User Manual
Page 3
I-FOLD ELECTRICAL INSTALLATION
1.
WARNING: Power MUST
BE DISCONNECT
ED from the machine before starting this procedure.
2.
Remove the back feeder, parallel & register guards.
3.
Install I-fold display mount (See Assy. Drawing FK2001426) onto register frame as shown in I-fold display mounting
location (See Page 33). Note: Before tightening the (4) socket head screws, locate display mount so that a gap
between the top of the register frame and the display mount is at maximum clearance, so that the register guard can be re-installed.
Figure 1
COM 2
Power Switch
Power Socket
1
Page 1 of 45
TP10497
See also other documents in the category Baumfolder Equipment:
- BAUM15: Pile Folder 1st Station (from 2005 on) (50 pages)
- BAUM15: Pile Folder 1st Station (from 1999 thru 2005) (50 pages)
- BAUM15: Control Panel (12 pages)
- BAUM18: Pile Folder 1st Station (from 2005 on) (50 pages)
- BAUM18: Pile Folder 1st Station (from 1999 thru 2005) (50 pages)
- BAUM20: Pile Folder 1st Station (from mid 2006) - Instruction Manual (68 pages)
- BAUM20: Pile Folder 1st Station (from mid 2006) - Parts Manual (79 pages)
- BAUM20: Pile Folder 1st Station (from mid 2006) - Parts Manual (157 pages)
- BAUM20: Pile Folder 1st Station (from mid 2006) - Parts Manual (81 pages)
- BAUM20: Pile Folder 1st Station (early 2006) (68 pages)
- BAUM20: Pile Folder 1st Station (in 2005) (68 pages)
- BAUM20: Pile Folder 1st Station (from 2002 thru 2004) (68 pages)
- BAUM20: Pile Folder 1st Station (from 1999 thru 2001) (50 pages)
- BAUM20: Pile Folder 2nd Station (from mid 2006) (1 page)
- BAUM20: Pile Folder 16page (from mid 2006) (1 page)
- BAUM20: Continuous Folder 1st Station - Parts Manual (1 page)
- BAUM20: Ifold Operation Manual (31 pages)
- BAUM20: Autoset Service Manual for Pile feed (19 pages)
- BAUM20: Sound Cover Installation (5 pages)
- BAUM20: 20 Kicker Assembly Installation (15 pages)
- BAUM20: 1300 series Pump Replacement Manual (11 pages)
- 714XA (49 pages)
- BAUM 26: 8PG Pre-slitter kit (13 pages)
- BAUM 26: Pre-slitter kit (early 2004) (8 pages)
- BAUM 26_30: Folder 1st Station Contfeed (46 pages)
- BaumCut 26.4: side table (5 pages)
- BaumCut 26.4 (For serials 69H1122 thru 76D1132) (98 pages)
- BaumCut 26.4 (For serials 76D1133 thru 78D1000) (104 pages)
- BaumCut 26.4 (For serials 78D1001 thru 78D1100) (104 pages)
- BaumCut 26.4 (For serials 78D1101 thru current) (104 pages)
- BaumCut 31.5 (For serials 76N1101 thru 78N1000) (104 pages)
- BaumCut 31.5 (For serials 78N1001 thru 700N100) (104 pages)
- BaumCut 31.5 (For serials 700N101 thru current) (98 pages)
- D2 Drill (9 pages)
- D3 Drill (from mid 2004 thru 2006) (9 pages)
- D3 Drill (from late 2003 thru mid 2004) (9 pages)
- D3 Drill (up to mid 2003) (9 pages)
- D5 Drill (from mid 2006 thru end 2006) (11 pages)
- D5 Drill (from 2003 thru mid 2006) (11 pages)
- D3HD Dril (11 pages)
- ND5 Drill (from 2000 thru 2002) (11 pages)
- 714XLT: Air-Operations Manual (from 2006) (13 pages)
- 714XLT: Air-Operations Manual (from 2001 thru 2005) (13 pages)
- 714XLT: Parts Manual (134 pages)