SDC 621 SERIES - Manual (Page 3)

INST-621LED.vsd REV - 04-08 Page 1
AFFIX LED LABEL WHERE SHOWN.
PUNCTURE LABEL WHERE IT COVERS THE HOLE IN
THE LID TO ALLOW THE LED TO PASS THROUGH.
MAKE SURE THE LED IS FULLY
SEATED AND THE WIRES SWING FREELY
INSERT WIRE PINS INTO
CONNECTOR SHELL AS SHOWN
FOR CORRECT POLARITY. PINS
ARE DIRECTIONAL. TAB ON PIN
MUST LOCK INTO CONNECTOR
INST-621LED.vsd REV - 04-08 Page 1
AFFIX LED LABEL WHERE SHOWN.
PUNCTURE LABEL WHERE IT COVERS THE HOLE IN
THE LID TO ALLOW THE LED TO PASS THROUGH.
MAKE SURE THE LED IS FULLY
SEATED AND THE WIRES SWING FREELY
INSERT WIRE PINS INTO
CONNECTOR SHELL AS SHOWN
FOR CORRECT POLARITY. PINS
ARE DIRECTIONAL. TAB ON PIN
MUST LOCK INTO CONNECTOR
INST-621LED.vsd REV - 04-08 Page 1
AFFIX LED LABEL WHERE SHOWN.
PUNCTURE LABEL WHERE IT COVERS THE HOLE IN
THE LID TO ALLOW THE LED TO PASS THROUGH.
MAKE SURE THE LED IS FULLY
SEATED AND THE WIRES SWING FREELY
INSERT WIRE PINS INTO
CONNECTOR SHELL AS SHOWN
FOR CORRECT POLARITY. PINS
ARE DIRECTIONAL. TAB ON PIN
MUST LOCK INTO CONNECTOR
INST-621LED.vsd REV - 04-08 Page 1
AFFIX LED LABEL WHERE SHOWN.
PUNCTURE LABEL WHERE IT COVERS THE HOLE IN
THE LID TO ALLOW THE LED TO PASS THROUGH.
MAKE SURE THE LED IS FULLY
SEATED AND THE WIRES SWING FREELY
INSERT WIRE PINS INTO
CONNECTOR SHELL AS SHOWN
FOR CORRECT POLARITY. PINS
ARE DIRECTIONAL. TAB ON PIN
MUST LOCK INTO CONNECTOR
INST-621LED.vsd REV - 04-08 Page 1
AFFIX LED LABEL WHERE SHOWN.
PUNCTURE LABEL WHERE IT COVERS THE HOLE IN
THE LID TO ALLOW THE LED TO PASS THROUGH.
MAKE SURE THE LED IS FULLY
SEATED AND THE WIRES SWING FREELY
INSERT WIRE PINS INTO
CONNECTOR SHELL AS SHOWN
FOR CORRECT POLARITY. PINS
ARE DIRECTIONAL. TAB ON PIN
MUST LOCK INTO CONNECTOR
INST-621LED.vsd REV - 04-08 Page 1
AFFIX LED LABEL WHERE SHOWN.
PUNCTURE LABEL WHERE IT COVERS THE HOLE IN
THE LID TO ALLOW THE LED TO PASS THROUGH.
MAKE SURE THE LED IS FULLY
SEATED AND THE WIRES SWING FREELY
INSERT WIRE PINS INTO
CONNECTOR SHELL AS SHOWN
FOR CORRECT POLARITY. PINS
ARE DIRECTIONAL. TAB ON PIN
MUST LOCK INTO CONNECTOR
INST-621LED.vsd REV - 04-08 Page 1
AFFIX LED LABEL WHERE SHOWN.
PUNCTURE LABEL WHERE IT COVERS THE HOLE IN
THE LID TO ALLOW THE LED TO PASS THROUGH.
MAKE SURE THE LED IS FULLY
SEATED AND THE WIRES SWING FREELY
INSERT WIRE PINS INTO
CONNECTOR SHELL AS SHOWN
FOR CORRECT POLARITY. PINS
ARE DIRECTIONAL. TAB ON PIN
MUST LOCK INTO CONNECTOR
INST-621LED.vsd REV - 04-08 Page 1
AFFIX LED LABEL WHERE SHOWN.
PUNCTURE LABEL WHERE IT COVERS THE HOLE IN
THE LID TO ALLOW THE LED TO PASS THROUGH.
MAKE SURE THE LED IS FULLY
SEATED AND THE WIRES SWING FREELY
INSERT WIRE PINS INTO
CONNECTOR SHELL AS SHOWN
FOR CORRECT POLARITY. PINS
ARE DIRECTIONAL. TAB ON PIN
MUST LOCK INTO CONNECTOR