S&S Cycle California X-Wedge Engines User Manual

Page 15

6- Throttle/Cables
Throttle Requirements

NOTE: S&S throttle bodies require the use of a two cable, pull open - pull closed throttle assembly. All models equipped with a single cable throttle
mechanism must be converted to the two cable, pull open - pull closed type. S&S offers a variety of these throttle assemblies.

Single, braided wire cable throttle mechanisms cannot mechanically close the throttle. If the throttle inadvertently sticks in the open
position, loss of control of motorcycle and personal injury to you or others may result.

Any motorcycle equipped with single cable throttle system must be converted to a two cable system. Kits with 36" (91cm), 39" (99cm), 42" (107cm),
48" (122cm), or 52" (132cm) length cables are available. Throttle assembly kits may be ordered separately. See descriptions on next page.
Two cable throttle systems designed for a butterfly type carburetor/throttle body have cable fittings that can simply be “plugged in” to the S&S
throttle body throttle linkage.

Optional S&S Two Cable Throttle Kits
Kits fit 1” (25.4mm) O.D. handlebars and can be used on most chassis. An adapter sleeve is available for use with handlebars having 7/8” (22.2mm)
diameter ends. Fittings on provided cables readily “plug in” to S&S® throttle bodies. Kits include one opening side cable, one closing side cable, left
and right handlebar grips, and handlebar clamps.

Throttle kit with 36” (91cm) cables PN 19-0450

•

Throttle kit with 39” (99cm) cables PN 19-0448

•

NOTE: 1981 to 1990 OEM style cables may be used as replacement cables for throttle kits above.

Gasoline is extremely flammable and explosive under certain conditions. Do not smoke or expose gasoline to sparks or open flame.

Gasoline fumes are toxic when inhaled. Perform installation in a well ventilated area away from open flames or sparks. Unwarranted
sparks and inadvertent engagement of starter while working on electrical components can cause serious injury or death.

Fuel hose must be clamped securely and not contact any hot surfaces where it could melt or catch fire, causing serious injury or death

A- Install new throttle assembly.

I- Install new throttle assembly and cables. Position grip and cables so cables can be angled towards throttle body for easy adjustment

and free operation.

II- Apply light coat of clean cable lubricant to cables and fittings. Loosen cable adjustment locknuts and turn adjusting screw so half of

the threads are exposed.

Throttle/Cable Assembly
A- Install throttle cables on the throttle body.

I- Remove throttle cable housing bracket, PN 11-2339.
II- Install opening side throttle cable barrel fitting and throttle cable in throttle linkage on appropriate side of throttle cable housing bracket.

Opening side cable housing outside diameter is smaller and measures .190” (4.826mm).

III- Repeat step II for closing side throttle cable. Closing side cable has a spring around inner cable wire.
IV- Reinstall throttle cable housing bracket on the throttle body.

B- Turn throttle cable adjusters to remove excessive free play. Test the throttle to ensure it opens and closes freely. The throttle should snap shut

when released. Turn handlebars to extreme left and open and close throttle, then turn bars to extreme right and repeat. If throttle binds, loosen
cable adjusters to put more free play in cables. Tighten the adjusting screw locknuts after final adjustments are made.

NOTE: Throttle grip assembly must be assembled correctly and work freely to prevent possible sticking during operation. Cable routing must be free of
tight bends to minimize cable to cable housing friction. Throttle must not bind and must snap shut to fully closed position when released.

Incorrect cable adjustment may cause throttle to stick open, causing loss of control of motorcycle, serious injury or death.

Throttle kit with 42” (107cm) cables PN 19-0482

•

Throttle kit with 48” (122cm) cables PN 19-0449

•

7/8” to 1” (22.2 to 25.4mm) adapter sleeve PN 19-0235

•

CAUTION

WARNING