MMF POS USB with Statistics Interface Kit User Manual
Usb interface

USB Interface /USB-HUB Combo Interface
Instruction manual / User Guide
Approved Date of Revision 7/10/2012 Doc. Instruction Manual
P/N: 531911900
USB Interface
USB Interface
USB Interface
USB Interface / USB
/ USB
/ USB
/ USB----HUB Combo Interface
HUB Combo Interface
HUB Combo Interface
HUB Combo Interface
GETTING STARTED:
GETTING STARTED:
GETTING STARTED:
GETTING STARTED:
If you have purchased a USB-HUB Combo, proceed by always connecting the standard USB interface which serves as
the cash drawer’s connectivity first. For both types of interfaces, please follow these steps:
Select Cash Drawer Number with Dip Switch
The MMF POS USB Interface Board’s Dip Switch is factory defaulted to either recognize the cash
drawer as drawer number zero (0) or seven (7), see Figure 1.0 Dip-Switch Position (Default Setting).
If user decides to assign another drawer number, please follow the pin configuration illustrated in
SWITCH SETTINGS Table 1.0 or label attached to the interface for correct pin orientation. MMF
recommends selecting cash drawer number one (1) as your option.
Connect the Power Supply (12VDC / .8 Amp)
Plug the small plug tip to the interface power port in the back of the cash drawer interface as illustrated in
Figure 1. Plug the power adapter end into a 120 Volt AC Recepticle.
Always connect the power supply before the USB Cable.
Connect USB Cable
Plug the Type B connector end to the USB Port of the interface as illustrated in Figure 1 and the Type A
Connector to the USB port of the Host Computer.
Test Functionality of Interface
Follow the steps detailed below for ‘USB Test Utility Installation’.
Install OPOS Drivers
Follow the steps detailed below for ‘MMF OPOS Drivers Installation’.
NOTE: Do not assign two (2) USB interface cash drawers within the same system with the same cash drawer number.
FIGURE 1.0
TABLE 1.0
SWITCH
SWITCH
SWITCH
SWITCH
SETTINGS
SETTINGS
SETTINGS
SETTINGS
DRAWER
DRAWER
DRAWER
DRAWER NUMBER
NUMBER
NUMBER
NUMBER
0
0
0
0
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
D
IP
D
IP
D
IP
D
IP
----S
W
IT
C
H
S
W
IT
C
H
S
W
IT
C
H
S
W
IT
C
H
SW1
SW1
SW1
SW1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
SW2
SW2
SW2
SW2
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
SW3
SW3
SW3
SW3
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SW4
SW4
SW4
SW4
RESERVED
Note: OFF is when pins are facing down (↓). ON is when pins are facing up (↑).
DIP-SWITCH POSITION
Default Setting: Drawer 0
Power Port
Connect 12V DC
Power Supply
Here
USB Port
Port of Cash Drawer
Interface
Connect Type B
Connector of USB
cable Here
1 2 3 4
5
This light should not be ON at any time
USB Interface
P/N#2261998USBA1-XX:
USB Interface KIT (Includes Power
Supplies & USB Host Cables)
P/N# 641-2575-00:
Cash Drawer Power Supply (12V dc)
P/N# 641-25BX-00:
USB Host Cable
USB-HUB Combo Interface
(A combination of our standard USB
Interface and a 4-Port HUB)
P/N# 2261998USBA1-XX:
USB-HUB Interface KIT (Includes Power
Supplies & USB Host Cables)
P/N# 641-2575-00:
Cash Drawer Power Supply (12V dc)
P/N# 641-25CE-00:
USB Hub Power Supply (5V dc)
P/N# 641-25BX-00:
USB Host Cable
Colored LEDS