Gardman Self Assembly Bird Table - Manual

Black
75% 50% 25%
Cyan
75% 50% 25%
Magenta
75 50 25
Yellow
75% 50% 25% Paper C+Y C C+M M M+Y Y C+M+Y
Black
75% 50% 25%
Cyan
75% 50% 25%
Graphix Digital 01775 680718
artwork
g r a p h i x d i g i t a l
tudor gables thary lane surfleet spalding
lincolnshire pe11 4bn united kingdom
t: +44 (0)1775 680718
e: [email protected]
www.graphixonline.co.uk
client:
date:
job no:
title:
size:
Gardman Ltd_AB
27.03.08
4948.2_A03072
SABT Instruction
A4 1pp
Cyan
Magenta
Yellow
Black
Cutter (do not print)
PMS
PMS
PMS
PMS
PMS
approval
method:
approved:
date:
Horizontal printer output check - this line measures 170mm
V
ertical printer output check - this line measures 75mm
Self Assembly Bird Table
Instructions
Please read these instructions carefully before commencing assembly.
Tools required: crosshead screwdriver, tape/ruler.
Contents
16 x 25mm screws
25 x 40mm screws
6 x 60mm screws
Instructions
Site out of reach of predators.
Care
We recommend that you clean your feeders and bird tables with a mild disinfectant solution
once every two months or more often in warm weather. Remove as much old food and debris
as possible. Wash and thoroughly rinse all items*. Periodically reposition your feeders and
tables to a different area within the garden to avoid an accumulation of unhygienic deposits.
* Wash equipment outdoors, wear gloves and wash hands thoroughly afterwards.
1 Roof assembly
2 Roof
supports
Base section 1 Tray assembly 1 Centre
pole
(2 sections)
2 Table
support
blocks
4 Legs
Step 1
1 Attach end caps to ridge piece
using 2 x 40mm screws. Do
not fully tighten screws.
2 Attach rebated feather edge
under ridge piece edge with
2 x 25mm screws each end.
3 Attach standard feather edge
to end caps using 2 x 25mm
screws.
4 Fully tighten ridge piece screws.
Roof Assembly
Rebated
feather
edge x 2
Ridge piece
End caps x 2
Feather
edge x 2
Step 2
1 Position base
section centrally
onto bottom of
centre pole.
2 Screw together
using 1 x 60mm
screw.
Base Assembly
Step 3
1 Screw top of four
legs to the centre pole
using 4 x 40mm screws.
2 Screw the legs, at
their mid point, to
the base assembly
using 4 x 60mm
screws.
3 Assemble centre
pole as shown
using 3 x 40mm
screws.
Pole & Leg Assembly
Step 4
Tray & Leg Assembly
1 Position table assembly
centrally on top of centre
pole and fix with 1 x 60mm
screw.
2 Screw the two table
support blocks to each
side of the centre pole.
Use 2 x 40mm screws per
support block.
3 Fix tray onto support blocks
using 2 x 40mm screws in
each piece.
Step 5
Roof Assembly
1 Attach the two roof supports
centrally onto the roof
assembly using 4 x 40mm
screws allowing roof
support to protrude
140mm below roof
assembly.
2 Position complete roof
assembly onto the tray
assembly and fix with
4 x 40mm screws from
underneath.
140mm
A03072
For Customer Services Telephone:
+44 (0) 1406 372227
4948.2_A03072 Instruction#B752D 27/3/08 3:28 pm Page 1