Fulltone Supa-Trem ST-1 - Manual (Page 2)

ST-1 Features
Page 2
BYPASS footswitch: The Fulltone-made 3PDT footswitch is the toughest switch you can get. The Supa-Trem is turned ON when the
green L.E.D. (light emitting diode) is lit up.
VOLUME mini-knob: This small knob only works when pedal is turned ON. When this knob is turned Full Counter Clockwise (CCW) you
should be at “unity gain,” meaning your level should be about the same as when the pedal is turned OFF, depending on settings.
RATE knob: This large knob controls the speed of the effect when pedal is ON. You may use either your fingers or your feet to adjust this
knob, making changes during a song a breeze!
RATE L.E.D. : This red L.E.D. always flashes in sync with the RATE setting, even when the pedal is turned off! This allows you to pre-set
the desired tempo before you turn the pedal on, making it easy to drop in on a song without sounding out of sync with the song’s rhythm.
SPEED footswitch: Stepping on this will get you either half or double whatever your current speed (RATE) is. It’s a great way to add drama
without getting out of sync with the song’s tempo...sort of what an organ player does with his leslie spinning speaker cabinet.
MIX knob: This large knob makes the tremolo effect stronger as it is turned CW, and more subtle as it is turned CCW. You may also use
your foot to adjust this knob.
HARD/SOFT footswitch: Allows you to go from normal tremolo to super-choppy square-wave tremolo on the fly.
Cool Trick! Turn MIX full CCW, make sure the HARD/SOFT switch is set to SOFT, and your pedal becomes an amazing Clean Boost
device when you turn it on...simply set the VOLUME knob to how ever much kick you want. NOW, if you want to add tremolo, simply step
on the HARD/SOFT footswitch and you’ll have a normal sounding sine-wave tremolo.
DC Power Options: You may ONLY run this pedal on the 9 volt battery (included) or on any 9Volt DC power supply as it’s a standard
2.1mm x 5.5mm barrel plug with “Negative to Center Pin” configuration. (as illustrated by the following diagram)
To access the battery, unscrew the two thumbscrews (located on the left and right sides of the pedal) and pull the housing apart. Replace
battery, put housing back together and re-install thumbscrews. Note: You may also use any 6/32 thread screw with a length between 3/16”
and a maximum of 3/8”. Unplug the guitar cable from INPUT when not in use to prolong battery life but if you have an adapter plugged in to
the DC outlet there is no need to unplug the guitar cable from the INPUT because our DC outlet is True-Bypass and disconnects the battery
supply line, thus keeping the battery fresh. The Fulltone FPS-1 is a great 9VDC regulated wall wart adapter.
WARRANTY:
Fulltone products carry a Limited 5 year Warranty to the original owner with proof of purchase that the product was bought from an Authorized Fulltone
Dealer. There is no need to register your product, simply keep a copy of your original sales receipt. The Warranty covers failure due to manufacturing errors only and is void if
any mod or repair is performed by anyone other than Fulltone AND/OR if we deem that any operator-caused abuse or damage has occurred, for example; the use of an
incorrect power supply, a dropped pedal, water damage, etc. Batteries are not Warranty-covered and Customer is always responsible for all shipping costs both to and from
Fulltone. Do not attempt to call Fulltone, instead, all Repair issues are handled by an email [email protected] to troubleshoot the possible problem and (only after
troubleshooting) for the scheduling of Warranty Repair. After we have deemed that a repair is necessary, we will email you an Acrobat PDF copy of our Return Authorization
Form (RA Form) and you will print it out, fill out all information, and include it with the device you are sending. Fulltone Musical Products Inc. is not responsible for and injuries
and/or damages related to the use of our products.
Fulltone Musical Products Inc.
11018 Washington Blvd. Culver City, CA 90232
for more info and expanded information/videos go to fulltone.com and/or youtube.com/fulltoneeffects
For sales related questions please email [email protected]
For Repairs/Technical related questions email [email protected]
C 2014 FMP Inc. All Rights Reserved
PHOTOCELL TRIMMER:
There is a trimmer inside the pedal that we
carefully set to get the optimal sound and feel
from this tremolo device. There’s no need for
you to touch this trimmer! If it is turned CW the
current to the photocell’s LED is increased, which
can intensify the tremolo effect up to a point.
Turning this trimmer CCW will decrease the
tremolo effect. We mark the “factory setting” with
a line or dot on the PCB, in case you adjust it and
then want to return to the stock setting.