Operation, 1 fill the fuel tank (gas models only), 2 fill hydraulic fluid – Echo LS21160 Owners Manual v.2 User Manual
Page 12: 3 starting a gas log splitter, 4 stopping a gas log splitter, 5 starting an electric log splitter, Operation 4 4, Warning, Important

8
LOG SPLITTER
Section
oPEraTion
4
4
4.3 STarTing a gaS Log SPLiTTEr
4.4 SToPPing a gaS Log SPLiTTEr
As with any other piece of outdoor equipment, getting the
feel for how your machine operates and getting to know
the best techniques for particular jobs are important to
overall good performance.
Move machine to a clear, level area outdoors before
starting. Do not operate in the vicinity of bystanders.
Warning
Move the machine to a clear, level area outdoors before
starting. Do not operate in the vicinity of bystanders.
1. Check engine oil and hydraulic oil levels before
starting.
2. Turn the fuel cut-off switch to the ON position, if
applicable.
3. Turn the engine switch to the ON position, if
applicable.
4. Place the throttle control midway between the SlOW
and FAST positions. If starting a cold engine, move the
choke control into the CHOKE position.
5. Pull the recoil starter until light resistance is felt. Then,
pull briskly. Repeat until the engine starts. Make sure
the starting cord retracts after each pull.
6. As the engine warms, gradually turn the choke off.
7. Move the throttle to the FaST position.
1. Move the throttle to the SLOw position.
2. On 160cc engines, stop the engine by pushing the
throttle all the way down to the STOP position. On all
other engines, stop the engine by turning the engine
switch to the OFF position.
3. Turn the fuel cut-off switch to the OFF position, if
applicable.
4.1 fiLL ThE fuEL TanK
(gaS modELS onLY)
use only those types of fuels that are recommended in
your engine owner’s manual.
To add fuel:
1. Stop engine, wait for all parts to stop moving and
disconnect spark plug wire. Allow the engine and muffler
to cool for at least three minutes.
2. Clean area around fuel fill cap and remove cap.
3. using a clean funnel, fill fuel tank to 1/2” below bottom
of filler neck to provide space for any fuel expansion.
Install fuel fill cap securely and wipe up any spilled
gasoline.
Warning
gasoline and diesel fuels are highly
flammable and their vapors are
explosive. To prevent personal injury or
property damage:
Store fuel only in approved containers,
in well ventilated, unoccupied buildings,
away from sparks or flames. A container
with a capacity of 2 gallons or less with a pouring spout
is recommended. Do not fill the fuel tank while the
engine is hot or running, since spilled fuel could ignite if
it comes in contact with hot parts or sparks from ignition.
Do not start the engine near spilled fuel. Never use fuel
as a cleaning agent. DO NOT MIX OIl WITH FuEl.
4.5 STarTing an ELEcTric Log SPLiTTEr
1. Plug the log splitter in to a 120 volt outlet.
2. Flip the switch on the motor to start it.
3. The log splitter is ready for operation.
4.6 SToPPing an ELEcTric Log SPLiTTEr
1. Flip the switch on the motor to turn it off.
2. unplug the log splitter.
imPorTanT
If you need to attach an extension cord to the log
splitter, make sure the cord is 12 gauge or greater.
4.2 fiLL hYdrauLic fLuid
The hydraulic tank is located in the back of the machine.
Check the fluid level with the dipstick before each use.
Check the fluid on level ground with the jack stand in the
down position. The hydraulic pump requires premium
hydraulic fluids containing high quality rust, oxidation, and
foam inhibitors. Do not overfill.
Fill the hydraulic fluid
tank with the ram retracted.