Echo 76824 Owners Manual v.3 - Manual (Page 10)

6 TURNTABLE CHIPPER
assemblY
2.1 Tires and rims (domesTic and s
models onlY)
2.2 Trailer hiTch (domesTic and s
models onlY)
Before inspecting or servicing any part of this machine, shut
off power source, disengage the hydraulics, remove igni-
tion key and make sure all moving parts have come to a
complete stop.
Warning
If any bolts or nuts are dropped in the machine, be sure to
remove them before starting the machine. Remove items
from the shredder area by removing the discharge screen.
imPorTanT
Mount tires and rims to the axle using the lug nuts.
Attach the fender supports to the trailer using three 1/2" x
3-1/2" hex bolts, washers & nuts.
Attach the fenders to the fender supports using four 3/8" x
1" carriage bolts, washers and nuts.
1.
2.
3.
s models:
Thread the wire harness through the hitch tube and slide
the hitch tube into the trailer frame. Secure using two 1/2" x
4-1/2" bolts, washers and nuts (provided in owner's kit).
Slide the hitch coupler onto the hitch tube from the top and
secure using 1/2" bolts, nuts and washers.
Thread the wire harness through the metal loop on the un-
derside of the coupler.
1.
2.
3.
2.3 rear sTabilizer
verify that the rear stabilizer is installed. To install the rear stabi-
lizer, slide the stabilizer into the corresponding bracket beneath
the rear of the chipper frame. Adjust the stabilizer and secure
with the provided snap pin.
domesTic models:
Thread the wire harness through the hitch tube and slide the
hitch into the trailer frame. Secure using two 1/2" x 4-1/2" bolts,
washers and nuts (provided in owner's kit).
Check the oil level and, if needed, fill the engine crankcase
with the type and amount of oil specified in the engine owner's
manual.
2.4 checKing/adding oil To engine
section
2.7 connecTing The baTTerY
To avoid sparks and a possible explosion or fire due to a
short circuit, do not touch the positive (+) battery terminal
and any surrounding metal with tools, jewelry or other metal
objects. When installing battery cables, connect the posi-
tive (+) cable first and the negative (-) cable last.
Warning
For best results use only clean, fresh, fuel. purchase fuel in
small quantities and store in clean, approved containers.
REFER TO ThE ENgINE OWNERS MANUAL FOR FURThER
FILLINg INSTRUCTIONS.
hydraulic fluid drives the feed roller. The machine was shipped
with fluid, as it was tested at the factory. however, check the
fluid levels before initial operation and add if necessary.
The hydraulic pump requires premium hydraulic fluids contain-
ing high quality rust, oxidation, and foam inhibitors. These include
premium turbine oils, ApI CD engine oils per SAE J183, M2C33F
or G automatic transmission fluids meeting Allison C-3 or Cater-
pillar To-2, and certain specialty agricultural tractor fluids.
2.5 checKing/adding hYdraulic fluid
2.6 filling The TanK
Fuel is highly flammable and its vapors are ex-
plosive. To prevent personal injury or property
damage:
Store fuel only in approved containers, in well
ventilated, unoccupied buildings, away from
sparks or flames. do not fill the fuel tank while the engine
is hot or running. Spilled fuel could ignite if it comes in
contact with hot parts or sparks from ignition. Do not start
the engine near spilled fuel. Never use fuel as a cleaning
agent.
danger
The machine may or may not have been shipped with a battery
depending on your area. If you did not receive a battery with
your machine, you will need to purchase one.
Use a battery that meets or exceeds the following specifications:
battery category, lawn and garden
bci group size u1
200-250 cca
7-3/4" X 5-3/16" X 7-5/16"
suggested source:
exide cutting edge, Type gT-h
After purchasing your battery, fill, charge and install the battery
according to the battery owners manual.
2