Snorkel SL30N-sn13300+ - Manual (Page 8)

8
COMPONENT INSPECTION OR SERVICES INTERVAL MODEL Y N R
Elevating Inspect for structural cracks Daily A
Assembly Check pivot points for wear 30 D A
Check mounting pin pivot bolts 30
D
A
for proper torque
Check linkage gear for wear 6 M A
Check elevating arms for bending 6
M
A
Grease linkage pins 30 D A
Grease linkage gear 30
D
A
Chassis Check hoses for pinch or Daily A
rubbing points
Check component mounting 6
M
A
for proper torque
Check welds for cracks Daily A
Lift Check the cylinder rod for wear 30 D A
Cylinder Check mounting pin pivot bolts 30
D
A
for proper torque
Check pivot pin snap rings 30 D A
Check seals for leaks 30
D
A
Inspect pivot points for wear 30 D A
Check fittings for proper torque 30
D
A
Entire Check for and repair Daily A
Unit collision damage
Check fasteners for proper torque 3
M
A
Check for corrosion-remove 6 M A
and repaint
Lubricate 30
D
A
Labels Check for peeling, missing, or Daily A
unreadable labels & replace
Wheel Check wheel assembly for play 30 D A
Bearings Repack wheel bearings 2
Y
A
(replace wheel bearings and
seals at 2000 hrs.)
Service Report
Date: ______________
Owner: _______________________________
Model No: ___________ Serial No: ________
Serviced By: ___________________________
Service Interval: ________________________
Routine Service Table Key
Interval
Daily=each shift (every day) or every eight hours
30
D
=every month (30 days) or every 50 hours
3
M
=every 3 months or 125 hours
6
M
=every 6 months or 250 hours
1
Y
=every year or 500 hours
2
Y
=every year or 1000 hours
Model
A= All Models
E= Electric Models
D= Dual Fuel Models
Y=Yes/Acceptable
N=No/Not Acceptable
R=Repaired/Acceptable
Routine Service
Use the following table as a guide for routine
maintenance. Inspection and maintenance shall
be performed by personnel who are trained
and familiar with mechanical and electrical
procedures. Refer to the Service Manual for
complete service instructions.
Please copy the following page and use the
Routine Service table as a checklist when inspect-
ing a machine for service.
COMPONENT INSPECTION OR SERVICES INTERVAL MODEL Y N R
Battery Check electrolyte level Daily A
System Check specific gravity 30 D A
Clean exterior 6
M
A
Check battery cable condition Daily A
Charge batteries Daily E
Clean terminals 6
M
A
Engine Oil Check level and condition Daily D
Check for leaks Daily D
Change oil filter 30 D D
Engine Fuel Check fuel level Daily D
System Check for leaks Daily D
Replace fuel filter 6 M D
Check air cleaner Daily D
Hydraulic Oil Check oil level Daily A
Change filter 6
M
A
Drain and replace oil 2
Y
A
Hydraulic Check for leaks Daily A
System Check hose connections 30
D
A
Check hoses for exterior wear 30 D A
Emergency Open the emergency lowering Daily A
Hydraulic valve and check for
System serviceability
Controller Check switch operation Daily A
Control Check the exterior of the cable Daily A
Cable for pinching, binding or wear
Platform Check fasteners for proper torque Daily A
Deck and Check welds for cracks Daily A
Rails Check condition of deck Daily A
Tires Check for damage Daily A
Check air pressure (50 psi-B78 x 13 ST) Daily A
Check lug nuts (torque to 90 ft. lbs. [123 Nm]) 30
D
A
Hydraulic Wipe clean 30 D A
Pump Check for leaks at mating surfaces 30
D
A
Check for hose fitting leaks Daily A
Check mounting bolts for proper torque 30
D
A
Check the drive coupling for proper
torque and alignment 1 Y A
Lubricate pump splines (Kohler Only) 6
M
D
Drive Motors Check for operation and leaks Daily A
Steering Check hardware & fittings 6
M
A
System for proper torque
Grease pivot pins 30
D
A
Oil king pins 30
D
A
Check steering cylinder for leaks & 30 D A
mounting bolts for proper torque