L.B. White Portable Gas Heaters - Manual (Page 4)

The parts identification guides on the following pages have
been designed to give a quick reference to component parts
used on all types of L.B. White construction heaters, such as
convection, circulating, direct spark ignition, and kerosene
heaters. The guides identify components not only used on
current production, but also on equipment that is of earlier
design. To use the guides properly, you should know the
model number of the heater and its design sequence. For
some heaters, there are no differences in components
regardless of design or age. Therefore, you will find
components are common, and identifying a specific design
sequence is not necessary.
Other heater models will refer to specific designs for parts
selection. You will need to obtain the design sequence level
to accurately determine the proper placement component.
This information is identified on the dataplate. Some
models may have the design sequence shown as the 4th
digit of the model number. For other models, the dataplate
will identify a configuration number. The design sequence is
the first digit of the configuration number.
Parts lists and schematics are shown on the following pages
for the respective heaters.
The parts guides also identify part numbers for the most
commonly requested components, wires, and hardware
items used on the heaters. If a wire, nut, or screw, etc. is not
identified, please contact the L. B. White Co. for parts
ordering information.
6 IN.
6 IN. 6 IN.
Without C Configuration N Number
MODEL AW075EHP3
SERIAL NO.:
L. B. WHITE CO., INC. W6636 L.B. WHITE ROAD ONALASKA, WI 54650 608/783-5691
A G S
DESI GN
CERTIFI ED
A A
A
MERI C N
SSOC
I ATI ON
MAXIMUM INPUT: 75,000 BTUH
TYPE FUEL: PROPANE VAPOR WITHDRAWAL
BURNER MANIFOLD PRESSURE 11 IN W.C. AT MAXIMUM INPUT
ELECTRICAL: 115 VOLTS A.C. 60 HZ SINGLE PHASE 1.4 AMPS
MIN. CLEARANCES FROM HEATER TO ADJACENT COMBUSTIBLE MATERIALS: REAR 1 FT SIDES 1 FT
TOP TO CEILING 1 FT BLOWER OUTLET 6 FT AND FUEL CONTAINER 6 FT
VENTILATION: 450 CFM OF AIR REQUIRED TO SUPPORT COMBUSTION.
MAXIMUM 13.5 INCHES W.C. AND MINIMUM 11.5 INCHES W.C. GAS SUPPLY PRESSURE
ACCEPTABLE AT INLET 0F HEATER FOR PURPOSE OF INPUT ADJUSTMENT.
POSITION HEATER AWAY FROM LIVESTOCK
AGRICULTURAL BUILDING HEATER
D Daattaappllaattee C Coom mppaarriissoonn
With C Configuration N Number
MODEL AW060
CONFIGURATION NO. AHPD210000
SERIAL NO.:
L. B. WHITE CO., INC. W6636 L.B. WHITE ROAD ONALASKA, WI 54650 608/783-5691
A G S
DESI GN
CERTIFI ED
A A
A
MERI C N
SSOCIATI O N
MAXIMUM INPUT: 60,000 BTUH
TYPE FUEL: PROPANE VAPOR WITHDRAWAL
BURNER MANIFOLD PRESSURE 10.0 IN W.C. AT MAXIMUM INPUT
ELECTRICAL: 115 VOLTS A.C. 60 HZ SINGLE PHASE 1.5 AMPS
MIN. CLEARANCES FROM HEATER TO ADJACENT COMBUSTIBLE MATERIALS: REAR 1 FT SIDES 1 FT
TOP TO CEILING 1 FT BLOWER OUTLET 6 FT AND FUEL CONTAINER 6 FT
VENTILATION: 240 CFM OF AIR REQUIRED TO SUPPORT COMBUSTION.
MAXIMUM 13.5 INCHES W.C. AND MINIMUM 11.5 INCHES W.C. GAS SUPPLY PRESSURE
ACCEPTABLE AT INLET 0F HEATER FOR PURPOSE OF INPUT ADJUSTMENT.
POSITION HEATER AWAY FROM LIVESTOCK
AGRICULTURAL BUILDING HEATER
Design
Sequence
Design
Sequence
DSPD120104
60,000 BTUH 170,000 BTUH
1050
10
CS170 296E
10 FT
11
625
11 11
Parts Identification Guide