Steele Products SP-PB140 User Manual
Page 2

Dear Customer
If you require any help with your product,
whether it is a Warranty claim, spare part or
user information, please phone our Help Line
888-896-6881 for an immediate response.
Introduction
Your new Steele® power tool will more
than satisfy your expectations. It has been
manufactured under stringent Steele® Quality
Standards to meet superior performance criteria.
You will find your new tool easy and safe to
operate, and, with proper care, it will give you
many years of dependable service.
Carefully read through this entire
Instruction Manual before using your new
Steele® Power Tool. Take special care to
heed the Cautions and Warnings.Your
Steele® power tool has many features that
will make you job faster and easier. Safety
performance and depend ability have been given
top priority to the development of this tool, making
it easy to maintain and operate.
Environmental protection
Recycle unwanted materials instead
of disposing of them as waste. All
tools, hoses and packaging should
be sorted, taken to the local
recycling center and disposed of in
an environmentally safe way.
WARNING
.
It may be more difficult to see the
laser line in conditions of bright
sunshine and on certain surfaces.
Description of symbols
The rating plate on your tool may show symbols. These
represent important information about the product or
instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
The ‘C’ and ‘US’ indicators adjacent to the
CSA Mark signify that the product has been
evaluated to the applicable CSA and ANSI/UL
Standards, for use in Canada and the U.S.,
respectively.
Specifications
Amp:
2.0
RPM:
2650 ft/min
Throat Depth:
9”
Cutting Capacity:
3-1/2”
Table Size:
11-13/16” x 11-13/16”
Blade Size:
59-1/2”
Bevel Angle:
0° to 45°
Laser class:
I
Laser wavelength:
650nm
Laser output power:
ᱽ 1mW
Replacement lamp:
120V Max 15W E12
Insulation class:
I “Earthed Appliance”
Weight:
40.3 lbs
V : volts
~ : alternating current
Hz : hertz
nm : nanometers
A : ampere
mW : milliwatt
Caution.
3
Read and understand all instructions.
Safety rules for laserlights
The laser guide used in the tool is Class I with a
maximum output of
1mw and a wavelength of
650nm. The laser guide does not normally present
an optical hazard, although staring at the beam may
cause flash blindness.
USER INFORMATION
CAUTION
.
The use of optical instruments with
this laser product will increase the chance of eye
damage.
Do not stare into the laser beam.
The laser shall be used and maintained in
accordance with the manufacturer’s instructions.
Never aim the beam at any person or an object
other than the work piece.
Always ensure the laser beam is aimed at a
sturdy work piece without a reflective surface,
i.e. wood or rough coated surfaces are
acceptable. Bright shiny reflective sheet or the
like is not suitable for laser use as the reflective
surface could direct the beam back at the
operator.
General safety instructions
WARNING.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
Save these instructions.
1. Keep guards in place and in working order.
2. Remove adjusting keys and wrenches.
3. Keep work area clean.Cluttered areas and benches
invite accidents.
4. Don’t use in dangerous environment. Don’t use
power tools in damp or wet locations, or expose
them to rain. Keep work area well lighted.
5. Keep children away. All visitors should be kept
safe distance from work area.
6. Make the workshop kid proof with padlocks,
master switches, or by removing starter keys.
7. Don’t force the tool. It will do the job better and
safer at the rate for which it was designed.
8. Use the right tool. Don’t force tool or attachment
to do a job for which it was not designed.
9. Use the proper extension cord. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and
overheating. The table on page 7 of this manual
shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt,
use the next heavier gage. The smaller the gage
number, the heavier the cord.
10. Wear proper apparel. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long
hair.
11. Always use safety glasses. Also use face or
dust mask if cutting operating is dusty.
Everyday eyeglasses only have impact
resistant lenses: they are not safety glasses.
12. Secure work. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and it frees both hands to operate the tool.
13. Don’t overreach. Keep proper footing and
balance at all times.
4