Gradall 534C-10 Parts Manual - Manual (Page 35)

2-2
Item Part No. Qty. Description Of Part
32 Ref DRIVE HUB, (see page 6-8 for
details)
33 9112-0004 1 R.H. STEERING KNUCKLE,
(see note #3)
34 8850-1006 2 HEX NUT, 3/8-16
35 8855-1011 6 LOCK WASHER, 3/8
36 8320-1144 2 HEX HD CAPSCREW, 3/8-16X5-3/4,
GR8
37 8867-1001 6 LUBE FITTING, STRAIGHT, 1/8
38 9108-1695 2 STEERING CYLINDER PIVOT PIN
39 9104-1598 AR SHIM, (.060 thick, see note #1)
40 Ref STEERING CYLINDER ASSY, (see
page 10-6 for details)
41 9116-6056 1 L.H. TUBE SUPPORT
9116-6055 1 R.H. TUBE SUPPORT
42 8820-1035 4 HEX HD CAPSCREW, 3/8-16X1,
GR5
43 8821-1121 2 SOCKET HD CAPSCREW,
1/2-13X6-1/2, GR8
44 9112-0003 1 L.H. STEERING KNUCKLE,
(see note #3)
45 9104-3247 2 SELF-ALIGNING BUSHING
46 8668-1572 12 HARDENED WASHER, 3/4
47 8320-1006 12 HEX HD CAPSCREW, 3/4-10X2, GR8,
(torque to 270-290 ft. lbs.)
48 8852-1208 2 HEX LOCKNUT, 1/2-13
49 9104-3222 4 CAPSCREW 12PT, 3/410X2, GR8,
(torque to 270-290 ft. lbs.)
50 9020-1918 AR SHIM, (10 gauge, see note #1)
51 8855-1153 2 LOCK WASHER, 5/8
52 8821-2321 4 SOCKET HD CAPSCREW,
5/8-11X3-3/4, GR8
53 9108-1177 1 REAR AXLE MOUNTING PIN
54 8510-1098 1 HEX NUT, 1-1/4-7
55 9116-6063 1 TIE ROD, (includes item 45)
56 9116-1066 AR SHIM, (.0598 thick)
57 9116-1067 AR SHIM, (.1046 thick)
58 9116-1068 AR SHIM, (.1345 thick)
59 9002-0247 1 HEX HD CAPSCREW, 1-1/4-7X6,
GR5
60 2460-1570 2 LIP SEAL
61 9112-3031 2 BUSHING
62 8850-1110 2 HEX NUT, 5/8-11
Item Part No. Qty. Description Of Part
9103-5240 1 STEERING KNUCKLE KIT, (includes
items 2, 4, 7 thru 14; 16 thru 23; 27 thru
31, 43, 48, 51, & two of item 52, one kit
does both sides)
9104-5152 AR STEERING CYLINDER PIN KIT,
(includes one each of items 1, 2, 3,
12, 21 thru 25, one kit needed for
each side)
1 8852-1312 2 HEX LOCK NUT, 3/4-10, (torque to
160-175 ft. lbs.)
2 9108-1415 2 DIRT SHIELD
3 9104-1481 2 STEERING CYLINDER PIN
4 9112-1239 2 BUSHING
5 9104-1439 2 TIE ROD PIN
6 8852-1306 2 LOCK NUT, 3/8-16
7 9112-1240 4 BUSHING
8 9112-3030 4 BACK-UP RING
9 8859-1032 4 O-RING
10 9112-3027 2 BUSHING
11 9112-3029 2 O-RING
12 8859-1104 4 O-RING
13 9112-1091 2 THRUST BUSHING
14 9104-1733 AR SHIM
15 9116-6012 1 REAR AXLE WELDMENT, (includes
items 10, 17, & 61)
16 8692-1268 2 LIP SEAL
17 9112-3028 2 BUSHING
18 9108-1693 2 UPPER KING PIN
19 8858-1323 4 RETAINING RING
20 8867-1022 4 LUBE FITTING, 90 DEGREES, 1/8
21 9104-1732 2 SPACER, (3/16 thick)
22 9104-1438 AR SPACER
23 8859-1019 2 O-RING
24 9104-1459 2 WASHER
25 8850-1416 2 HEX JAM NUT, 1-14, (torque to
225-250 ft. lbs.)
26 8320-1140 2 HEX HD CAPSCREW, 3/8-16X2-3/4,
GR8
27 9114-1424 2 LOWER KING PIN
28 9104-1449 AR SHIM, (.060 thick, see note #2)
29 9104-1450 AR SHIM, (.0478 thick, see note #2)
30 9104-1451 AR SHIM, (.106 thick, see note #2)
31 9104-1596 AR SHIM, (20 gauge, see note #2)
NOTE #1: Cylinder base end must be free to rotate. Shim steer cylinder base end as required to maintain a total max.
gap of 1/16".
NOTE #2: Shim bottom knuckles as required to maintain no more than 1/32" movement. Shim top knuckles as
required to maintain no more than 1/16" gap. Must have a minimum of one shim.
NOTE #3: All machines need to bore Steering Knuckles to use items 4 & 7. See diagram on previous page. unless you
have purchased new Steering Knuckles part number, 9112-0003 & 9112-0004.
NOTE #4: See option section for details on the Rear Axle Rework Kit and the Rear Axle Advantage Kit.
CHASSIS & ATTACHING PARTS
Rear Axle & Attaching Parts
Starting Serial No. 0344436
Starting Serial No.0266063
Original Issue 6-96
Revised 3-1-99
PCN 970126, 971313,
980725 - JH
* Revised parts list, service notes and illustration.