Gradall 524D LoPro User Manual
Page 29
Item
Part No.
Qty.
Description Of Part
30
9148-0002
1
R.H. KNUCKLE
31
8850-1110
2
HEX NUT, 5/8-11
32
8821-2321
2
SOCKET HD CAPSCREW,
5/8-11X3-3/4, GR8
33
9002-8740
2
GREASE FITTING, FEMALE
34
8870-1021
2
NIPPLE, 1/8X2
35
8850-1006
2
HEX NUT, 3/8-16
36
8320-1144
2
HEX HD CAPSCREW, 3/8-16X5-3/4
37
9140-3372
2
BASE END STEER CYLINDER PIN
38
8871-1280
2
HEX SOCKET PIPE PLUG, 1/8
39
9140-3065
AR
KINGPIN SHIM, (see note # 1)
9140-3066
AR
KINGPIN SHIM, (see note # 1)
40
Ref
STEERING CYLINDER, (see page10-
5 for details)
41
9148-6011
1
L.H. TUBE SUPPORT
9140-6099
1
R.H. TUBE SUPPORT
42
8820-1035
4
HEX HD CAPSCREW, 3/8-16X1, GR5
43
8821-2285
2
SOCKET HD CAPSCREW, 3/4-10X5,
GR8
44
8821-2272
2
SOCKET HD CAPSCREW, 5/8-11X8,
GR8
45
8852-1210
2
HEX LOCKNUT, 5/8
46
9148-0001
1
L.H. KNUCKLE
47
9104-3246
2
SELF-ALIGNING BUSHING, (tie rod)
48
8867-1001
4
LUBE FITTING, STRAIGHT, 1/8
49
9138-6010
1
TIE ROD WELDMENT, (includes
item 47)
50
8668-1572
12
HARDENED WASHER, 3/4
51
8320-1006
12
HEX HD CAPSCREW, 3/4-10X2
52
9104-3222
4
12 POINT SCREW, 3/4-10X2
53
8855-1154
2
LOCKWASHER, 3/4, (hi-collar)
54
9108-1177
1
REAR AXLE PIN
55
9002-0247
1
HEX HD CAPSCREW, 1-1/4-7X6, GR5
56
8510-1098
1
LOCKNUT, 1-1/4-7
57
9108-1691
1
SHIM, (.1046 thick)
58
9103-1009
1
SHIM, (.0598 thick)
59
9020-6846
1
SHIM, (.1345 thick)
60
9108-3449
4
HEX NUT, 1/2-13
Item
Part No.
Qty.
Description Of Part
9141-5040
AR
STEERING CYLINDER PIN KIT,
(includes one each of items 1 thru 8,
one kit needed for each side)
1
8852-1312
2
LOCKNUT, 3/4-10, (torque to
160-175 ft-lbs)
2
9108-1415
2
DIRT SHIELD
3
9104-1732
2
SPACER
4
8859-1019
2
O-RING
5
8859-1104
2
O-RING
6
9134-3052
2
ROD END STEER CYLINDER PIN
7
9140-3162
2
HARDENED WASHER
8
8850-1420
2
HEX JAM NUT, 1-1/4-12, (torque to
280-305 ft-lbs)
9
9140-3082
2
TIE ROD PIN
10
8855-1011
8
LOCKWASHER, 3/8
11
8320-1021
2
HEX HD CAPSCREW, 3/8-16X3
12
8852-1306
2
HEX LOCKNUT, 3/8-16
13
9140-3145
8
WIPER SEAL
14
9140-3034
2
LOWER BUSHING
15
9140-3146
2
O-RING
16
8859-1108
2
O-RING
17
9140-1081
2
THRUST BUSHING
18
9138-6009
1
REAR AXLE WELDMENT, (includes
items 14, 23 & 28)
19
9140-3163
AR
KINGPIN SHIM, (see note # 2)
9140-3164
AR
KINGPIN SHIM, (see note # 2)
9140-3165
AR
KINGPIN SHIM, (see note # 2)
9140-3166
AR
KINGPIN SHIM, (see note # 2)
20
9140-3078
2
LOWER KINGPIN
21
9140-3067
2
RETAINING WASHER
22
8821-1068
2
SOCKET HD CAPSCREW,
3/8-16X5/8, GR8
23
9140-3031
2
UPPER BUSHING
24
9148-3024
2
UPPER KINGPIN
25
8858-1325
2
SNAP RING
26
9112-3092
4
STUD, (see note #3)
27
8540-1340
4
HARD WASHER
28
9140-3033
2
PIVOT TUBE BUSHING
29
Ref
DRIVE HUB, (524D), (see page 6-6
for details)
Ref
NON-DRIVE HUB, (522D), (see page
6-6 for details)
FRAME & ATTACHING PARTS
Rear Axle & Attaching Parts
Starting Serial No. 0191001
Original Issue 6-01
2-3
NOTE #1: Cylinder base end must be free to rotate. Shim Steering Cylinder base end as required
to maintain a total maximum gap of 1/16".
NOTE #2: Shim bottom Knuckles as required to maintain no more than 1/32" movement. Shim top
Knuckles to maintain no more than 1/16" gap. Must have a minimum of one shim.
NOTE #3: Install 5/8 long thread on Stud into Drive Hub (shortest length threads on Stud)
LK