Ooking, P the, Elevision – Philips 20PF8946-37 User Manual
Page 3: Tv, fm
3
H
OOKING
U
P THE
T
ELEVISION
A
combination antenna receives normal broadcast chan-
nels (VHF 2–13 and UHF 14–69). Your connection is
easy because there is only one 75
Ω
(ohm) antenna plug on
the back of your TV, and that’s where the antenna goes.
1
If your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has flat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
2
Push the round end of the adapter (or antenna) onto the
75
Ω
(ohm) plug on the bottom of the TV. If the round end
of the antenna wire is threaded, screw it down finger tight.
A
NTENNA
TV, FM
Antenna Connection:
Outdoor or Indoor Antenna (Combination VHF/UHF)
The combination antenna receives normal broadcast
channels 2-13 (VHF) and 14-69 (UHF).
Y
our Cable TV input into your home may be a single
(75 ohm) cable or use a cable box decoder. In either
case the connection is very simple. Follow the steps
below to connect your cable signal to your new television.
Direct Cable Connections:
This connection will supply Stereo sound to the TV.
Connect the open end of the round Cable Company sup-
plied cable to the 75
Ω
input on the bottom of the TV. Screw
it down finger tight.
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound to the TV.
The sound from the cable box will be mono.
1
Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
2
Using a separate round coaxial cable, connect one end to the
OUT(put) (TO TV) plug on the back of the Cable Box.
3
Connect the other end of the round coaxial cable to the
75
Ω input on the bottom of the television. Screw it down fin-
ger tight.
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the
back of the cable box to CH 3 or 4, then tune the cable box on the
TV to the corresponding channel. Once tuned, change channels at
the cable box, not the television.
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound to the TV.
1
Connect the open end of the round Cable
Company supplied cable to the cable signal
IN(put) plug on the back of the Cable Box.
2
Using an RCA type Video Cable, connect one end
of thecable to the Video (yellow) (or ANT, your
cable box may belabeled differently) Out jack on
the cable box and the otherend to the Video end of
the composite adapter included with the TV.
.
3
Using an RCA type Audio Left and Right Cable,
connect oneend to the left and right Audio Out
L and R jacks (red and white) on the cable box.
Connect the other ends to the Audio end of the
composite adapter cable included with the TV.
Connect the adapter into the AV In jack on the
bottom of the TV.
NOTE: Use the Source button on the remote control to
tune to the AV1 channel for the cable box signal. Once
tuned, change channels at the cable box, not the television.
Pressing the Source button repeatedly will scroll all the
AV input channels, including the presently tuned channel.
C
ABLE
/C
ABLE
B
OX
TV
Direct Cable Connection
Cable Box with Audio/Video Outputs Connection:
Cable Signal IN
from the Cable Company
T
o load the supplied batteries into the remote:
1
Remove the battery compartment door on the back of the
remote.
Place the two batteries in the remote. Be sure the (+) and (–)
ends of the batteries line up correctly (the inside of the case is
marked).
Reattach the battery compartment door.
2
3
R
EMOTE
C
ONTROL
B
ATTERIES
1
20" model only
15"/17"/23" models only
20" model only
15"/17"/23" models only
Direct Cable Connection
Cable signal
coming from
Cable Company
(Round 75
Ω
coaxial cable)
20" model
only
15"/17"/23"
models only
Round 75 Ω
Coaxial Cable
from Antenna
300 to 75-ohm
Adapter
1
2
3
3
1
Video Cable
(Yellow)
Audio Cables L & R
(Red / Whiite)
Jack Panel at bottom of TV
Jack Panel at bottom of TV
Jack Panel at bottom of TV
Jack Panel at bottom of TV
Jack Panel at bottom of TV
Jack Panel at bottom of TV
Output Channel Switch
Round 75 Ω Coaxial Cable
2
3
Jack Panel at back of Cable Box with AV option
20" model only
15"/17"/23" models only
Jack Panel at bottom of TV
Jack Panel at bottom of TV
2
1
Twin
Lead
Wire
1
1