Behringer Ultra-Low Noise Design 12-Input 2/2-Bus Mixer with Premium Mic Preamplifiers UB1204-PRO - Manual (Page 10)

10 EURORACK UB1204FX-PRO/UB1204-PRO User Manual
LEVEL METER
The high-precision level meter accurately displays the appropriate signal level.
LEVEL SETTING:
When recording to a digital device, the recorder’s peak meter should not exceed
0 dB. This is because, unlike analog recordings, slightly excessive levels can create
unpleasant digital distortion.
When recording to an analog device, the VU meters of the recording machine
should reach approx. +3 dB with low-frequency signals (e.g. kick drum). Due to
their inertia VU meters tend to display too low a signal level at frequencies above
1 kHz. This is why, for example, a Hi-Hat should only be driven as far as -10 dB.
Snare drums should be driven to approx. 0 dB.
◊ The peak meters of your EURORACK display the level virtually
independent of frequency. A recording level of 0 dB is recommended
for all signal types.
MODE (UB1204FX-PRO only)
The MODE switch determines whether the channels’ SOLO switch operates as PFL
(Pre Fader Listen) or as solo (Solo In Place).
PFL
To activate the PFL function, depress the MODE switch. The PFL function should,
as a rule, be used for GAIN setting purposes. The signal is sourced pre-fader and
assigned to the mono PFL bus. In the “PFL” setting, only the left side of the peak
meter operates. Drive the individual channels to the 0 dB mark of the VU meter.
Solo
When the MODE switch is not depressed, the stereo solo bus is active. Solo is
short for “Solo In Place”. This is the customary method for listening to an
individual signal or to a group of signals. As soon as a solo switch is pressed,
all channels in the control room (and headphones) that have not been selected
are muted thereby retaining stereo panning. The solo bus can carry the output
signals of the channel pan controls, the aux sends and the stereo line inputs.
The solo bus is, as a rule, switched post-fader.
◊ The PAN control in the channel strip offers a constant power
characteristic. This means that the signal is always at a constant level,
irrespective of its position in the stereo panorama. If the PAN control
is moved fully left or right from center, the level increases by 4 dB
in that channel. This ensures that, when set in the center, the audio
signal is not louder. For this reason, with the solo function activated
(Solo in Place), audio signals from the channels with PAN controls that
have not been moved fully to the left or right are displayed at a lower
volume than in the PFL function.
As a rule, solo signals are monitored via the control room outputs and
headphones connector and are displayed by the level meters. If a solo switch is
pressed, the signals from the 2-TRACK INPUT, Alt 3-4 and main mix are blocked
from the control room outputs, the headphone connector and the level meter.
MAIN SOLO (UB1204FX-PRO only)
The MAIN SOLO LED lights up as soon as a channel or aux send solo switch is
pressed. The MODE switch also has to be set at “Solo”.
PFL (UB1204FX-PRO only)
The PFL LED indicates that the peak meter is set to PFL mode.
PHONES
You can connect headphones to this 1/4" TRS connector. The signal on the PHONES
connection is sourced from the control room output.
Fig. 2.12: PHONES connector
2.3.7 Alt 3-4 and main mix fader
Fig. 2.13: Alt 3-4 and main mix fader
Use the high-precision quality faders to control the output level of the Alt 3-4
subgroup and main mix.
2.4 Rear view of UB1204FX-PRO/UB1204-PRO
2.4.1 Main mix outputs, alt 3-4 outputs and control
room outputs
Fig. 2.14: Main mix outputs, Alt 3-4 outputs and control room outputs
MAIN OUTPUTS
The MAIN outputs carry the MAIN MIX signal and are on balanced XLR connectors
with a nominal level of +4 dBu.