Philips TransDock micro - Manual (Page 5)

9
EN
G
LI
SH
8
6. To control the overall volume of your music while
using your PhilipsTransDock micro, use the car
radio’s volume control, not the iPhone volume.
Turning your Philips TransDock micro on and off
Your PhilipsTransDock micro will turn on and off
automatically with your car.
To manually turn your PhilipsTransDock micro on or
off while your car power is on, press and hold the dial
for approximately 5 seconds.
Finding empty radio frequencies using IntelliTune
To find an empty frequency using IntelliTune:
1. Press the dial on your PhilipsTransDock micro.This
will activate the IntelliTune search.While it is
searching, the word IntelliTune will appear on your
TransDock micro’s display.
2. Once IntelliTune finds an empty frequency, it will
display “Tune Radio to XXX.X”.Then, tune your
FM radio to that station and begin enjoying your
iPhone music over your car stereo.
Manually finding empty radio frequencies
Your PhilipsTransDock micro also
allows you to manually tune the
transmitter to desired FM
frequencies.Turn your Philips
TransDock micro dial to the right
to tune to higher stations and left
to tune to lower stations.
Using PhilipsTransDock micro
Detailed instructions
1. Turn on your car radio and set it to FM radio mode.
2. Insert your PhilipsTransDock micro into your car’s
power outlet.
D
Note: You can also slightly alter the angle of your
TransDock micro by tilting the dial head up or down.
See drawing below.
3. Plug the Connector Cable into the iPhone dock
connector.
4. To activate your PhilipsTransDock micro’s IntelliTune
feature, press the dial.Your PhilipsTransDock micro
will display the word IntelliTune as it searches for the
optimal frequency.This should only take a few
seconds. Once the search is complete, the display
will instruct you to tune your radio to the frequency
found by IntelliTune.
5. Match the FM station on your radio with the
corresponding FM frequency shown on your
TransDock micro’s display. Click Play on your iPhone
to enjoy your music over your car’s FM radio.
Tips for manually finding an empty station:
• Be sure to search the entire spectrum of
FM frequencies.
• When using scan/seek on your car’s radio, if your
tuner stops on 101 and then jumps to 103, look
in the 102 frequencies for empty stations.
•Try tuning to a strong station, then backing down
two frequencies - for example 103.5 to 103.1.You
can often find empty frequencies this way.
D
Note: If that frequency is taken, scan to the
next station and try again.
Settings and features
To enter the Settings Menu press and hold your
PhilipsTransDock micro dial until the display flashes
“Settings”.Then, turn the dial to scroll through the
various Settings, and press the dial to enter your desired
Setting.Turn the dial to the right or left to view the
chosen Settings options, and press the dial to confirm
your selection. Once you’ve made your selection, you
will return to the Settings Menu. Press the center button
to exit the Settings Menu.
D
Note: Your PhilipsTransDock micro will
automatically exit the Settings Menu after a few
seconds of inactivity.
Preset Store
Preset Store allows you to save up to four preset
stations.The default presets are 88.1, 94.9, 100.9,
and 107.9.
To store your own preset stations, follow these simple
steps:
1. Using the dial, tune PhilipsTransDock micro to the
station you’d like to set – turning right to tune to
higher stations and left to tune to lower stations.
2. Press and hold the dial to enter the Settings Menu.
3. Once in the Settings Menu, scroll to Preset Store
and press the dial to select. Next, scroll to and
select the preset number (SET 1, SET 2, SET 3,
or SET 4) and press to select.
4. Repeat steps 1-3 to store the remaining presets.
D
Note: Your new preset will override the preset
that was last saved, including the default presets.
Preset Mode
Preset Mode gives you the option to scroll through
your presets in Manual Mode.
To turn Preset Mode on, follow these simple steps:
1. Press and hold the dial to enter the Settings Menu.
2. Scroll to Preset Mode and press the dial to select.
Then choose Preset Mode On and press to select.
Now you can scroll through the four presets (P1,
P2, P3, P4) in Manual Mode.