Behringer UB1622FX-PRO - Manual (Page 9)

9
EURORACK UB1622FX -PRO /UB1832FX -PRO /UB2222FX -PRO /UB2442FX -PRO
+
When used in this way, the effects device should
be set at 100% effect.
Fig. 2.12: Stereo aux return and
stereo aux return (to aux send) controls
STEREO AUX RETURN 1/2 (TO AUX SEND)
The two right-hand STEREO AUX RETURN controls have a
special function: they can be used to add an effect to a monitor
mix. An example follows (UB1622FX-PRO wired to an effects
device):
Monitor mix with effect
In this instance, your effects device should be set up as follows:
the AUX SEND 2 jack should be connected to the L/Mono input of
your effects device, with its outputs coming back into the STEREO
AUX RETURN 1 jacks.
Connect the AUX SEND 1 jack output to the amplifier of your
monitor system. The AUX SEND 1 master control determines the
overall volume of the monitor mix.
Using the STEREO AUX RETURN (TO AUX SEND) control, the
effect signal can now be blended into the monitor mix.
You can easily use the headphones distribution amplifier
BEHRINGER POWERPLAY PRO HA4600/HA4700/HA8000 to
provide four (HA8000: eight) stereo headphone mixes for your
studio.
The following table shows which jacks on the console can be
used for this purpose.
@‘‡r hyÃrssrp‡†Ã
qr‰vprà rprv‰r†Ã
†vthyÃs ‚€
Ã
@‘‡r hyÃrssrp‡†Ã
qr‰vprà ‚ˆ‡r†Ã†vthyÃ
ihpxǂ
UurÃrssrp‡Ã†vthyÃ
rhpur†Ã‡urÀ‚v‡‚ Ã
€v‘Évh
«
AUX SEND !
STEREO AUX
RETURN Ã
connectors
STEREO AUX
RETURN (TO AUX
SEND ) control
AUX SEND
STEREO AUX
RETURN !Ã
connectors
MONITOR switch of
the FX/AUX Ã! RET
AUX SEND Ã!
STEREO AUX
RETURN connectors
Г‚ Г!
STEREO AUX
RETURN Ã (TO AUX
SEND ) control
AUX SEND !
STEREO AUX
RETURN Ã
connectors
STEREO AUX
RETURN (TO AUX
SEND ) control
AUX SEND Ã
STEREO AUX
RETURN !Ã
connectors
STEREO AUX
RETURN ! (TO AUX
SEND ! ) control
V7!##!AYQSP
‚ƒ‡v‚hy)
V7 %!!AYQSP
V7 '"!AYQSP
V7!!!!AYQSP
Tab. 2.1: Connectors and controls for monitor mix with effect
STEREO AUX RETURN FX
On consoles UB1622FX-PRO and UB1832FX-PRO this is the
STEREO AUX RETURN 2, on consoles UB2222FX-PRO and
UB2442FX-PRO this is the STEREO AUX RETURN 3.
Use the STEREO AUX RETURN FX control to determine the
level of the signal routed from the AUX RETURN FX jacks to the
main mix. If nothing is connected to these jacks, the output of the
built-in effects module will appear.
MAIN MIX / TO SUBS
This switch routes the signal fed in via the STEREO AUX
RETURN FX jacks either to the main mix (not pressed) or to the
submix (pressed).
On the UB2442FX-PRO you can select which subgroup the
signal is assigned to (switches 1-2 / 3-4, to the right of MAIN MIX /
TO SUBS).
SOLO RETURNS
Additionally, this model allows you to route the aux returns
together to the solo bus and the PFL bus. The LED lights up when
Solo is on.
STEREO AUX RETURN 4 (UB2442FX-PRO only)
This control behaves the same way as the other stereo aux
returns. Additionally, it provides for a simple monitor path using
the switch CTRL ROOM & PHONES ONLY.
CTRL ROOM & PHONES ONLY
Use this switch to route the signal appearing at the AUX
RETURN 4 jacks to the control room and headphones outputs.
2.3.6 Supplement to UB1832FX-PRO
The UB1832FX-PRO has a stereo fader for the AUX RETURN
FX and offers a variety of routing options: MUTE disables the
effect return (but not PFL of course!), SOLO routes it to the Solo
or PFL busses, SUB to the subgroups and MAIN to the main mix.
Fig. 2.13: The FX/AUX 2 return fader of the UB1832FX-PRO
MON
The MON switch routes the signals appearing at the AUX
RETURN 2 jacks to the monitor path, along with the monitor signals
from the channels.
If you wish to route the effect signal to the monitor mix, you
can also switch aux 1 to pre-fader, drive the effect device from
the aux 1 output and return the effect signal via AUX RETURN 2
to the monitor signal.
2. CONTROL ELEMENTS AND CONNECTORS