Black & Decker Linea Pro WP1500K - Manual (Page 11)

11
ENGLISH
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth wire
is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must be
replaced by the manufacturer, authorized
Black & Decker Service Center or an equally qualified
person in order to avoid damage or injury. If the power
cord is replaced by an equally qualified person, but
not authorized by Black & Decker, the warranty will
not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Accessories must be rated for at least the speed recommended
on the tool warning label. Wheels and other accessories
running over rated speed can fly apart and cause injury.
Hold tool by insulated gripping surfaces when performing
an operation where the polishing tool may contact hidden
wiring or its own cord. Contact with a “live” wire will make
exposed metal parts of the tool “live” and shock the operator.
Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
Always wear eye protection.
Be sure bonnet is snugly installed on pad.
Keep hands and fingers away from rotating bonnet.
Before turning the switch to the ON position, be sure
the pad is free to revolve harmlessly.
Inspect the bonnet frequently for wear, dirt or imbedded
debris.
Caution! Do not allow the power cord to contact the
rotating bonnet as it may become quickly tangled around it. If
this occurs, turn tool OFF and unplug the power cord before
attempting to untangle the cord. If the cord is damaged, have
it repaired or replaced at your local tool repair station:
Never use a damaged or torn bonnet.
Wear proper clothing, short sleeves, nothing loose or
bulky, such as shop coat, etc.
Do not turn tool on unless the polishing bonnet is against
surface being polished.
Be extremely careful when polishing around sharp or
protruding objects on the car body.
Caution! Do not use abrasive or rubbing compounds. The
abrasive nature of these products can damage painted surfaces.
Caution! Wear appropriate hearing protection during use.
Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
USE OF EXTENSION CORDS
Make sure the extension cord is in good condition before using.
Always use the proper size extension cords with the tool – that
is, proper wire size for various lengths of cord and heavy enough
to carry the current the tool will draw. Use of an undersized
cord will cause a drop in line voltage resulting in loss of power
and overheating. For proper size cords see chart below.
SPECIFIC SAFETY RULES
Minimum gage for cord sets
Volts Total length of cord in feet
120V~ 0-25 26-50 51-100 101-150
220V~ 0-50 51-100 101-200 201-300
Ampere rating
More No more American wire gage
than than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not recommended
V ........... Volts
A ........... Amperes
Hz ......... Hertz
W........... Watts
min........ minutes
........ Alternating current
........ Direct current
n
0
.......... No-Load speed
........ Class II construction
........ Earthing terminal
........ Safety alert symbol
.../min.... Revolutions or
reciprocation per
minute
Read instructions manual
Use eye protection
Use ear protection