Toshiba DVR70 - Manual (Page 35)

35 EN
In
tr
od
uct
ion
Con
n
ec
ti
on
s
P
la
yb
ac
k
E
d
it
ing
Ot
he
rs
Fu
nct
ion
S
e
tu
p
Recor
d
ing
VH
S Fu
nc
ti
on
s
Basi
c Se
tu
p /
TV
Vi
ew
Op
eration
1
Press [TIMER SET] to cancel the timer-standby
mode.
2
Press [TIMER PROG.].
“Timer Programming” list will appear.
3
A) To delete the timer programme:
1) Select the programme you want to delete using
[K \ L], then press [ENTER\OK].
2) Select “Delete” using [K \ L], then press
[ENTER \OK].
Confirmation window will appear.
3) Select “Yes” using [K \ L], then press [ENTER\OK].
B) To correct the timer programme:
1) Select the programme you want to correct using
[K \ L], then press [ENTER\OK].
2) Select “Programme Change” using [K \ L], then press
[ENTER \OK].
3) Correct the timer programme by using [K \ L \ { \ B],
then press [ENTER \OK].
4
Press [TIMER PROG.] to exit.
5
Press [TIMER SET] to return to the timer-
standby mode.
To check the timer programming in progress
Press [TIMER PROG.].
Note
• If a timer recording is proceeding, that programme is
highlighted in red. In such a case, you cannot select any
other programmes.
• When you check the timer programming in progress by
pressing [TIMER PROG.] during operations of the
component (DVD or VHS) which is not currently used for the
timer recording, the programme will not be highlighted. In
this case, you cannot select other programmings.
On the front panel:
Press [STOP C].
On the remote control:
1
Press [STOP C].
2 Select “Yes” using [K \ L], then press
[ENTER \OK].
The error number appears on “Timer Programming” list.
The error programme will be displayed in gray with an error
number.
The error numbers indicate:
• The error programme will be deleted once you check the
error in the programme list, or once you cancel the timer-
standby mode and re-enter it.
Checking, Cancelling or Correcting the
Timer Programming Information
Stop the Timer Recording in Progress
If the Timer Programming did not
Complete Correctly
E1–E22, E37–E39 Recording error
E23–E24 Unrecordable disc
E25/E51 • Copy prohibited programme
• Cannot record because of the NTSC /
PAL-60 signal is received.
E26–E28 Copy prohibited programme
E29 Disc protected
E30 Disc full
E31 Already recorded 99 titles (video mode)
E32 Already recorded 99 titles (VR mode)
E33 Already recorded 999 chapters
E34 No space for Control Information
E35 PCA (Power Calibration Area) full
E36 Already finalised video format disc
E40 • There are some unrecorded parts due
to the overlapped timer programmes.
• Recording did not start at the start
time.
E41 Power failure
E42 No disc
E43 Already 49 titles recorded (+VR mode)
E44 Already 254 chapters recorded (+VR
mode)
E45 Copy prohibited programme
E46 It is impossible to record additionally on
a disc recorded by other units when
setting “Make Recording Compatible” to
“OFF”. (+VR mode)
1/1
E40 03/12 7:00 9:00 1 TF1
03/12 10:00
Date Start End CH
Timer Programming
STTL
VPS/PDC
THU
New Programme
E9TK2FD_EN.book Page 35 Wednesday, July 29, 2009 12:16 PM