Toshiba BDX1100 - Manual (Page 14)

1
E
ng
lis
h
6 Customizing
This. section. describes. the. various. setting.
option.of.this.BD.player..
If the setup option is grayed out, it means
the. setting. cannot. be. changed. at. the.
current.state.
General Setting
1..Press.SETUP.button.on.the.remote.
control.The.Setup.Menu.appears.
System Screen Saver On
On
On
More...
More...
Move cursor key to select menu option
then use “OK” key to select
Language Disc Auto Playback
Playback CEC
Security Easy Setup
Network Load Default
... General Setting ...
SETUP Exit
2. Press  to select an option, then press
.to.access.
3. Press / to.select.a.setup.option.and
press ..
4. Select.the.setting.you.wish.to.change
and press OK to confirm.
- Press  to.return.to.the.previous.menu.
[System]
To.change.the.following.system.option.to.
personalize.your.BD.player .
• [Screen Saver]
Turn.On.or.Off.the.screen.saver.mode.
It.helps.to.protect.the.TV.screen.
{.On.}.–.Set.the.screen.saver.active.
after.approximately.10.minutes.with.no.
operation.
-.The.BD.player.will.switch.to.standby.
mode.if.there.is.no.operation.after.the.
screen.saver.is.engaged.for.
approximately.10.minutes.
{.Off.}.–.Turn.off.the.screen.saver.
mode..
• [Disc Auto Playback]
Turn.On.or.Off.the.disc.automatic.
playback.switching.mode.
{On}.–.The.disc.playback.automatically.
after.loading.
{Off}.–.Turn.off.disc.auto.playback.
mode.
• [CEC]
This.player.supports.REGZA-LINK.which.
uses.the.HDMI.CEC.(Consumer.
Electronics.Control).protocol..You.can.
use.one.single.remote.control.to.control.
all.REGZA-LINK-compliant.devices.that.
are.connected.through.HDMI.connectors.
{On}.-.Turns.on.REGZA-LINK.features.
-With CEC on, during TV standby with
the BD player on, pressing SETUP, PLAY/
PAUSE.will..power.on.the.TV.
{Off}.-.Disables.REGZA-LINK.features.
• [Easy Setup]
Re-configure some settings. It is the same
as."Load.Default".of.steps.4-8.
Tip:
For setting osd and TV resolution and TV aspect.
• [Load Default]
Reset.all.settings.of.BD.player.to.initial.
default.state.
-.Follow.the.instruction.on.the.TV.screen.
to confirm the default setting operation.
1..Select.Load Default.
2..A.dialogue.box.pops.up.shown.as.
below..Select.OK..
Load Default
Cancel
Do you want to load default?
OK
3.It.may.take.awhile.when.loading.
default.is.in.progress..Please.wait...
Load Default
30%
Loading default, please wait...
4..TV.will.display.as.follow:
Welcome
OK Next
to the Toshiba BD Player Setting Wizard.
Some simple settings are suggested before you
begin. You can also access detailed settings
from the Setup Menu.
5. Press OK, enter language setting. . Press OK, enter language setting.
Press/ to.select.a.language.option.
Choose
Previous
an OSD language before starting.
The language selected will be applied not only
here but also in other OSD windows, menus
etc.
English
OK Next