Pioneer DJM-850-W - Manual (Page 22)

Category SW Name SW Type MIDI assignment Trigger/Toggle Transmitted data
BEAT EFFECTS
EFFECT
SELECT
DELAY Switch CC 042 2 OFF=0, ON=127
ECHO Switch CC 055 2 OFF=0, ON=127
UP ECHO Switch CC 061 2 OFF=0, ON=127
SPIRAL Switch CC 043 2 OFF=0, ON=127
REVERB Switch CC 054 2 OFF=0, ON=127
TRANS Switch CC 053 2 OFF=0, ON=127
FILTER Switch CC 059 2 OFF=0, ON=127
FLANGER Switch CC 050 2 OFF=0, ON=127
PHASER Switch CC 057 2 OFF=0, ON=127
ROBOT Switch CC 051 2 OFF=0, ON=127
SLIP ROLL Switch CC 058 2 OFF=0, ON=127
ROLL Switch CC 046 2 OFF=0, ON=127
REV ROLL Switch CC 047 2 OFF=0, ON=127
SND/RTN Switch CC 062 2 OFF=0, ON=127
CH
SELECT
CH1 Switch CC 034 2 OFF=0, ON=127
CH2 Switch CC 035 2 OFF=0, ON=127
CH3 Switch CC 036 2 OFF=0, ON=127
CH4 Switch CC 037 2 OFF=0, ON=127
MIC Switch CC 038 2 OFF=0, ON=127
CF.A Switch CC 039 2 OFF=0, ON=127
CF.B Switch CC 040 2 OFF=0, ON=127
MASTER Switch CC 041 2 OFF=0, ON=127
TIME
Switch CC 013 — —
Switch CC 045 —
TIME value (When FLANGER, PHASER
or FILTER is selected, the value is halved.
When a negative value is selected, it is set
to a positive value.)
LEVEL/DEPTH Switch CC 091 — 0-127
ON/OFF
! When an effect
other than [SND/
RTN] is selected at
BEAT EFFECT Button CC 114 — OFF=0, ON=127
ON/OFF
! When [SND/RTN]
is selected at BEAT
EFFECT
Button CC 064 — OFF=0, ON=127
MIC
HI Control CC 030 — 0-127
LOW Control CC 031 — 0-127
SOUND COLOR FX
NOISE Button CC 085 Trigger/Toggle 1 OFF=0, ON=127
GATE Button CC 105 Trigger/Toggle 1 OFF=0, ON=127
CRUSH Button CC 086 Trigger/Toggle 1 OFF=0, ON=127
FILTER Button CC 087 Trigger/Toggle 1 OFF=0, ON=127
Fader Start
FADER START 1 Button CC 088 Trigger/Toggle OFF=0, ON=127
FADER START 2 Button CC 089 Trigger/Toggle OFF=0, ON=127
FADER START 3 Button CC 090 Trigger/Toggle OFF=0, ON=127
FADER START 4 Button CC 093 Trigger/Toggle OFF=0, ON=127
HEADPHONES
MIXING Control CC 027 — 0-127
LEVEL Control CC 026 — 0-127
Timing Clock — Timing Clock — —
Fader Start
FADER START 1 Note 102 — BACK CUE = 0, PLAY = 127
FADER START 2 Note 103 — BACK CUE = 0, PLAY = 127
FADER START 3 Note 104 — BACK CUE = 0, PLAY = 127
FADER START 4 Note 105 — BACK CUE = 0, PLAY = 127
MIDI
START Button START — —
STOP Button STOP — —
1 When turning one button on switches another button from on to off, MIDI on and off messages are sent from the two buttons.
When there is no button that switches off, only the MIDI on message is sent from the button that was pressed.
2 When switched from one position to another position, the MIDI ON and OFF signals are sent respectively from both positions.
! When the [START/STOP] button is pressed for over 1 second, MIDI messages corresponding to the positions of the buttons, faders and controls are sent in a bundle
(Snapshot).
The MIDI Snapshot sends all MIDI messages other than MIDI start and MIDI stop.
22 En