Pioneer SX-20-S - Manual (Page 8)

03 Controls and displays
8
En
Display
1 H (Headphones)
Lights when both speakers A and B are switched off.
2 RDS indicators
Lights when an RDS broadcast is received.
3 ST
Lights when a stereo FM broadcast is being received in
stereo mode.
4 TUNED
Lights when a normal broadcast channel.
5 Sleep timer indicator
Lights when the receiver is in sleep mode.
6 PRESET
Lights when the tuner preset mode is selected.
7 MEM
Blinks when a radio station is registered.
8 Character display
Displays various system information.
9 kHz/MHz
Lights when the character display is showing the
currently received AM/FM broadcast frequency.
10 Preset information
Shows the preset number of the tuner.
11 DIRECT
Lights when the TONE DIRECT mode is switched on.
Remote control
5 2 1 3 4 7
11 10
6
8 9
SLEEP
APD
SPEAKERS
RDS
PTY MUTE
VOLUME
MEM
P.SCAN
INPUT FM/AM
SACD/CD
BASS
NETWORK AUDIO PLAYER
SACD PLAYER
RETURN HOME MENU
FUNC
SETUP
ENTER
TREBLE
PHONO NETWORK RECORDER
FM MODE
SEARCH DISPLAY
DIMMER TONE DIRECT SURROUND
1 2 3
4 5 6
A
B
7 8 9
0
STANDBY/ON
STEREO RECEIVER
BALANCE
T/P MODE
1
2
13
14
15
16
17
18
3
4
5
6
7
9
10
11
12
8
1  STANDBY/ON
Switches the receiver between standby and on.
2 Numeric buttons (0 ~ 9)
Press to select or to store preset.
3 TONE DIRECT
Press to select the TONE DIRECT mode (page 12).
4 SURROUND
Press to select the surround sound options (page 12).
5 RDS control buttons
SEARCH – Use to select the search mode (page 11).
PTY – Use to search for RDS program types
(page 11).
DISPLAY
– Use to display the RDS information
(page 11).
6 Tuner control buttons
FM MODE – Press to select the desired FM mode
(Stereo or monaural) (page 10).
P.SCAN
– Press to scan the stations in the preset
sequence (page 10).
T/P MODE
– Press to select the tuning mode or the
preset mode (page 10).
MEM
– Press to store preset stations (page 10).
7 /
At the tuning mode, use to find radio frequencies.
At the preset mode, use to select preset radio stations.
Also used when setting up the receiver.
8 BALANCE
When adjusting the sound volume balance, press to
enter the balance mode (page 11).
9 Input function buttons
Press to select an input source. These select the
component connected to the corresponding input on the
rear panel.
INPUT – Press repeatedly to select desired input
function. Use to change the input source. The
source changes as below.
SACD/CD
 NETWORK  PHONO 
RECORDER  FM/AM  Return to the beginning.
10 Tone control buttons
BASS +/– – Use to adjust Bass (page 11).
TREBLE +/– – Use to adjust Treble (page 11).
11 SACD PLAYER control buttons
Use to control Pioneer SACD/CD player.
12 NETWORK AUDIO PLAYER control
buttons
Use to control Pioneer network audio player.
13 SLEEP
Press to change the amount of time before the receiver
switches into standby (10 min – 20 min – 30 min – 60 min
– 90 min – Off). You can check the remaining sleep time
at any time by pressing SLEEP once.
14 APD
Use to change the Auto Power Down function setting
(page 12).
15 SPEAKERS A/B buttons
These buttons allow you to select various combinations
of speakers as follows:
• To drive A speakers, press SPEAKERS A button
(SPK A is displayed).
• To drive B speakers, press SPEAKERS B button
(SPK B is displayed).
• To drive both A and B speakers, press SPEAKERS A
and B buttons in order (SPK A B is displayed).
• When using headphones for private listening, press
these buttons in order to switch off the speakers A
and B (SPK OFF is displayed, and H indicator
lights).
16 DIMMER
Dims or brightens the display. The brightness can be
controlled in four steps.
17 MUTE
Mutes/unmutes the sound.
18 VOLUME +/–
Use to set the listening volume.