AEG TS 250 K - Manual (Page 26)

23
English
Support panels or any oversized workpiece to minimize the risk of
wheel pinching and kickback. Large workpieces tend to sag under
their own weight. Supports must be placed under the workpiece near
the line of cut and near the edge of the workpiece on both sides of the
wheel.
Keeping rip fence parallel to the saw blade.
MOVE the rip fence out of the way when cross-cutting.
Keep the floor area free of loose material e.g. chips and cut-offs.
Replace the table insert when worn
Adjust the riving knife as described in this instruction manual. Incorrect
spacing, positioning and alignment can make the riving knife ineffec-
tive in preventing kickback.
The handle lock must always be engaged when transporting the
circular table saw.
Do not use the top protective cover as a handle for transportation!
Before transporting the machine, make sure that the top protective
guard covers the top section of the saw blade.
In spite of compliance with all relevant design regulations, dangers may
still present themselves when the machine is operated, e.g.
- workpiece parts being thrown off,
- parts of damaged tools being thrown off,
- noise emissions,
- wood dust emissions.
SPECIFIED CONDITIONS OF USE
Use this circular saw to cut only wood and wood like products.
Do not use this product in any other way as stated for normal use.
MAINS CONNECTION
Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect to
sockets without an earthing contact as the design conforms to safety
class II.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under “Technical Data” fulfills all the relevant regulations and the direc-
tives 2011/65/EU (RoHs), 2004/108/ EC, 2006/42/EC and the following
harmonized standards have been used:
EN 61029-1:2009 + A11:2010
EN 61029-2-1:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2008
Winnenden, 2013-06-17
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
MAINTENANCE
Remove dust regularly. Remove the sawdust which has accummulated
inside the saw in order to avoid the risk of fire.
Use only AEG accessories and spare parts. Should components need to
be replaced which have not been described, please contact one of our
AEG service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the machine type printed as well as the six-digit No. on the label and
order the drawing at your local service agents or directly at: Techtronic
Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before starting the
machine.
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before
carrying out any work on the machine.
Wear ear protectors!
Always wear goggles when using the machine.
Wear gloves!
Always keep hands away from the path of the saw blade.
Never expose tool to rain.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with household
waste material! In observance of European Directive
2002/96/EC on waste electrical and electronic equipment
and its implementation in accordance with national law,
electric tools that have reached the end of their life must
be collected separately and returned to an environmen-
tally compatible recycling facility.
Class II construction, tool in which protection against
electric shock does not rely on basic insulation only, but
in which additional safety precautions, such as double
insulation or reinforced insulation, are provided.
GB