Silent Call PP1004-2 - Manual

5095 Williams Lake Road, Waterford Michigan 48329
(800) 572-5227 v/tty web:
http://www.silentcall.com
Installation and Operating Instructions
Pendant Pager Transmitter
Model PP1004-2
Switch settings
The Silent Call system is digitally coded. The code sent by the transmitter must match the code that your receiver has been set for.
All Silent Call receivers and transmitters leave the factory set for the default code of 1, 2 and 3 = OFF and 4 and 5 = ON. Unless you
have changed the code in your receiver from the factory default setting OR you have the new Sidekick II Receiver, Good
Vibrations, Vibra- Call or Omni Page you do not need to change the switch settings in your transmitter.
Note** The Pendant Pager is factory set so switches 6 through 9 are in the up (ON) position which represents light/strobe only.
If you are using the new Sidekick II Receiver (#SK09214-2), the Good Vibrations (#GV1097-2), the Vibra-Call (#VC4002-2)
or the Omni Page (#OP1097-2) you will need to set your Pendant Pager so that it will activate either Sound, Phone, Door, CO
or Weather.
The code switches are accessed by removing the back cover of the transmitter. Positions 1 through 5 determine the code that the
transmitter sends when it activates. These 5 switches must match you receiver exactly. Positions 6-9 determine which light activates
on your receiver.
Turn Switch 6 to the OFF position for SOUND
Turn Switch 7 to the OFF position for PHONE
Turn Switch 8 to the OFF position for DOOR
Turn Switch 9 to the OFF position for FIRE
Turn Switch 6, 7, & 8 to the OFF position for CO
Turn Switch 6, 7, 8 & 9 to the OFF position for Weather
Range:
100 foot range if used with the following receiver: Sidekick Receiver Model # SK09214, Lamp Lighter Model # LLS-04 & Crystal
Reflections Model # CR30.
200 foot range if used with the following receivers: Good Vibrations Receiver Model # GV1097-2, Omni Page Receiver Model #
OP1097-2, or Vibra-Call Receiver Model # VC4002-2
500 foot range if used with the following receiver: Sidekick II Receiver Model # SK09214-2
Power:
Operates on (1) 12 volt battery
Technical Support
For technical support on this or any other Silent Call product, please feel free to contact us. You can reach us by phone at 800-572-
5227 (voice or TTY) or by Email at
[email protected]
Limited Warranty
Your transmitter is warranted to be free of defects in material and workmanship for five years from the date of initial purchase. During that time, the
unit will be repaired or replaced free of charge when shipped prepaid to Silent Call Communications. To obtain warranty service, contact Silent Call
to obtain a return material authorization. This warranty is void if the defect is caused by customer abuse or neglect.
FCC Regulations Manual Addendum
Remote Control Transmitter
Model No: SCXMIT01
IMPORTANT REGULATORY NOTICE
Changes or modification not expressly approved by the manufacturer for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
In addition the following information is supplied as support documentation for the associated FCC SDoC Receivers that can be used with this transmitter:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
Factory Setting
Code Switches