Silverline 500W Hammer Drill - Manual (Page 6)

www.silverlinetools.com
5
500W Hammer Drill 265897
referred to in this manual. Always refer servicing to qualified
service personnel. Never remove any part of the casing unless
qualified to do so; this unit contains dangerous voltages.
• Use of a residual current device (RCD) will reduce the risk of
electric shock.
NEVER CONNECT THE BROWN OR BLUE WIRE TO THE
EARTH PIN OF THE 13 AMP PLUG. IF IN DOUBT CONSULT A
QUALIFIED ELECTRICIAN
Dangerous environment
• Do not use power tools in damp or wet conditions, or expose
them to rain. Provide adequate surrounding work space and
keep area well lit. Do not use power tools where there is a risk
of explosion or fire from combustible material, flammable
liquids, flammable gasses, or dust of an explosive nature.
When using power tools avoid contact with any earthed
items such as pipes, radiators, cookers, refrigerators, metal
baths and taps.
Protect yourself from vibration
• Hand held power tools may produce vibration. Vibration can
cause disease. Gloves to keep the operator warm may help to
maintain good blood circulation in the fingers. Hand held tools
should not be used for long periods without a break.
Maintain your power tool
• Ensure all ventilation holes are kept clear at all times.
Overheating and fire may otherwise result.
Always disconnect
• Before changing fittings or accessories, always ensure that
your tool is disconnected from the power source.
Switch off before connecting
• Ensure that the power tool is switched off before connecting to
the power source. If the power tool stops unexpectedly, turn
the power switch to off.
Do not abuse the power cord
• Be sure your cable or extension cable is in good condition.
Always have a damaged cable or extension cable replaced at
an authorised service centre before using it. Never yank or pull
the cable to disconnect it from the power socket. Never carry
your tool by its cable. Keep the cable away from damp, heat,
oil, solvents, and sharp edges.
Don’t leave the tool running unattended
• Always wait until your tool has completely stopped functioning,
and has been unplugged, before leaving i
Before Use
• Carefully unpack and inspect your power drill. Fully familiarise yourself
with all features and functions of the tool.
• Ensure that all parts of your power drill are present and in good condition.
If any part is missing, or damaged, have such parts replaced before
attempting to use this tool.
Operating Instructions
Side handle
• The side handle (7) should always be used when drilling.
• Always hold the drill firmly using both hands.
• The side handle can be adjusted to best suit the work to be performed.
• To adjust the side handle, rotate the handle grip anti-clockwise, this
will loosen the handle assembly. Move the side handle to the required
position, and secure by rotating the handle grip clockwise.
Operating the chuck
The chuck (1) can be opened by using the included chuck key. •
To close the jaws rotate the chuck key clockwise, to open the jaws rotate •
the chuck key anticlockwise.
Do not operate the drill to open or close the chuck. Doing this will cause
•
permanent damage to your tool.
On/off switch
• To start the drill, squeeze the on/off switch (5).
• To stop the drill, release the on/off switch.
Lock on button
• The drill is equipped with a lock on button (4). This allows the on/off
switch to be locked into the “on” position for tasks that require extended
continuous running.
• To use the lock on function, depress the lock on button whilst squeezing
the on/off switch, the on/off switch can then be released and the drill
will continue to run.
• To stop the drill, squeeze, then release the on/off switch.
Speed control
• The speed of the drill can be varied between 0 and 2800RPM.
• The speed is adjusted by rotating the speed control dial (6).
Reversing
• The direction of the drill can be changed using the reverse switch (3).
• To run the drill in a clockwise direction, push the reverse switch to
the right.
• To run the drill in an anti-clockwise direction, push the reverse switch
to the left.
• Do not attempt to move the reverse switch whilst the drill is running.
• Do not attempt to run the drill with the reverse switch in a mid position.
Hammer selection
1 Chuck
2 Hammer selection switch
3 Reverse switch
4 Lock on button
5 On/off switch
6 Speed control dial
7 Side handle
Product Familiarisation
265897_manual.indd 5 22/12/09 09:37:21