Barksdale UDS7-BX - Manual (Page 2)

List of functions: (xxxx = 125% f. s.)
Dialog item Value Description
MENÜ -1...9999 Primary display, e.g. the value selected in the DISP menu appears here
DISP ..... Display value which should be permanently in the display:
act actual measured value
sp1 switching point SP1
sp2 switching point SP2
max maximum peak value
min minimum peak value
ACT. -1...9999 Display of actual measured value in bar
UNIT Fixing the unit
bar bar = bar The unit is shown in the display appr.
psi psi x = psi x 10 every 30 sec. for appr. 5 sec.
psi psi = psi
HPa HPa = Hekto-Pascal
mbar mbar = millibar
UND Unit display “on” or “off”
SP.1 ..... none switching output deactivated
wind window technology
stnd standard evaluation SP2
erro error output
ON-1 -1 ... xxxx Switch-on point for SP1; if the ON value is smaller than the OFF
value the switching point evaluation is falling
OFF-1 -1 ... xxxx Switch-off point for SP1
DLY1 0,0s...9,9s Switch-on / switch-off delay for SP1 in seconds
INV-1 ..... Inversion of switching output SP1
hlfs high-level-fail-save (normally open function)
Ilfs low-level-fail-save (normally closed function)
SP.2 ..... none switching output deactivated
wind window technology
stnd standard evaluation SP2
erro error output
ON-2 -1 ... xxxx Switch-on point for SP2;
if the ON value is smaller than the OFF value
the switching point evaluation is falling
OFF-2 -1 ... xxxx Switch-off point for SP2
DLY2 0,0s...9,9s Switch-on / switch-off delay for SP2 in seconds
INV-2 ----- Inversion of switching output SP2
hlfs high-level-fail-save (normally open function)
Ilfs low-level-fail-save (normally closed function)
MAX -1 ... xxxx Display of peak value
CLRH ----- Delete the maximum value memory
----- no deletion
clr delete value
3 2
Dialog item Value Description
CDLY 0,0s...9,9s Time setting to delete the maximum value memory after switching
point SP1 is reached (manual deletion is still possible)
MIN -1 ... xxxx Display of peak value “Min“
CLRL ----- Delete the minimum value memory
----- no deletion
clr delete value
OFFS -9,9 ...+xx Measured value offset in bar
CUT 0,0 ... +xx Cut-off. e.g. signal suppression at measuring range start in bar
DLDS 0,0 ... 9,9s Time delay for currently displayed value in seconds
ERRC ----- Error messages:
0: -ok- no error
1: max exceeding pos. measuring range
2: min exceeding neg. measuring range
3: dig1 switching output 1 error
4: dig2 switching output 2 error
5: anao analog output error
6: sens sensor error
7: data data error (EEProm)
8: prog program error
9: cal calibration error
V7.X Lev0...Lev2 Programming lock indication (see code)
Version display with actual input level:
0 : only display of operating parameters, no changes possible
1 : only switching points can be set (“max” and “min” memories)
2 : release user level (all operating parameters for customer)
LITH 20 ... 100 Change display brightness 20...100%
(only for units with Dot-Matrix display)
AOZS 0 ... 9999 Scale the analog output - start value (e. g. 0 bar = 4 mA)
AOFS 0 ... 9999 Scale the analog output - end value (e. g. 400 bar = 20 mA)
(output signal start value always corresponds to the display initial
value, e. g. 0 bar = 4mA)
Maximum turn-down 4 : 1, i.e. at values below 25 % of the
measuring range the analog output is switched off
CODE 000...999 Security Sequence
Lev1: 471 Allow to change switching point parameters only
Lev2: 740 Able to reconfi gure all allowable parameters
Lev0: 999 All parameters will be lock
OPT ----- For internal use only
(onlyV7.X)
For models shipped before Nov. 23, 2013