Dynatek D2K14-1SE - Manual (Page 2)

ID2K14-1SE www.dynaonline.com 2010-2012 Hyundai Genesis 2.0T Coupe - 2
ID2K14-1SE.01
EXPANSION
PORTS 1 & 2
USB
CONNECTION
WIRE CONNECTIONS:
To insert wires into the Dynatek 2000SE first remove the rubber plug on the
backside of the unit and loosen the screw for the corresponding input.
Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into
the hole of the Dynatek
2000SE until is stops and
then tighten the screw.
Make sure to reinstall the
rubber plug.
NOTE: If you tin the wires
with solder it will make
inserting them easier.
DYNATEK 2000SE
INPUT ACCESSORY GUIDE
DYNATEK 2000SE IGNITION MODULE INPUTS
Input 1 and input 2 are used for switches. The switches must be configured in the Dynatek
2000SE software.
Map: The Dynatek 2000SE has the ability to hold two different base maps. You can switch
on the fly between these two base maps when you connect a switch to input 1 or 2.
You can use any open/close type switch. The polarity of the wires is not important.
Shifter: These inputs are for use with a Dynatek quickshifter. Insert the wires from the
Dynatek quickshifter into input 1 or 2. The polarity of the wires is not important. (Set
to input 2 by default.)
Launch: A switch may be connected to input 1 or 2 to activate launch control. A clutch lever
switch may be used by connecting the + side of the clutch switch to input 1+ or input
2+. When launch control is activated, the Dyna 2000SE will limit RPM to the target
set in the software.
Speed Limiter: A switch may be connected to input 1 or 2 to activate a speed limiter. You can
use any open/close type switch. The polarity of the wires is not important. The speed
limiter must be configured in the Dynatek 2000SE software.
Speed: If your application has a speed sensor then you can tap into the signal side of the
sensor and run a wire into this input. This will allow you to calculate gear position
in the Dyna 2000SE software. Once gear position is setup you can alter your
map based on gear position and setup gear dependent kill times when using a
quickshifter.
Analog: This input is for a 0-5v signal such as gear position, boost, etc. Once this input is
established you can alter your ignition curve based on this input in the Dyna 2000SE
software.
USING DYNA 2000SE CONTROL CENTER SOFTWARE
Insert the CD provided into your computer’s cd-rom drive. The launch program will run
automatically. If auto-run is disabled, double-click the My Computer icon then double-click
the CD drive icon. Double-click Dyna 2000SE.exe to manually start the CD.
Click Install Software and follow the on-screen instructions to install the Dyna 2000SE
software. The Dyna 2000SE software will be stored in C:\Program Files\Dyna 2000SE.
Click Map Database. All maps will automatically be installed to the C:\Program Files\Dyna
2000SE\maps folder.
Connect the USB cable from the computer to the Dynatek 2000SE. Verify the cable is fully
seated in the Dynatek 2000SE.
Run the Dyna 2000SE software by double-clicking the program icon installed on your
desktop or on your start menu. Click Open Map File and select a map file. Click Send Map.
The values in the map represent a change in degrees of ignition timing. A value of 10
in the map indicates at that throttle position and RPM range the ignition timing will be
advanced 10 degrees from the stock timing. If the value is -10, then the ignition timing will
be retarded 10 degrees from the stock timing. The Dyna 2000SE software allows a value of
+20 to -20 in each cell.
TROUBLESHOOTING
If the STATUS LED does not come on when the ignition is switched on, there is no power
to the Dynatek 2000SE. Make sure that you have the ground connected properly either
directly to the battery ground, or to a lug on the frame that is grounded.
If the LED comes on, but the vehicle does not run on all cylinders, double check all
connections at the injector, making sure the connectors are seated properly.
NOT USED
ANALOG
SPEED
INPUT 2+
INPUT 2-
INPUT 1+
INPUT 1-