Adder Technology AdderView CATx EPS-S8 - Manual (Page 78)















USB Country Code
Some.computers.query.the.keyboard.to.find.
out.its.country.code.and.key.layout..These.
computers.use.this.information.to.configure.
the.way.that.they.interpret.the.data.coming.
from.the.keyboard.and.so.it.is.important.for.
the.correct.country.information.to.be.supplied..
Not.all.keyboards.report.country.information.
and.two.different.styles.of.keyboard.may.be.
connected.to.the.AdderView.CATx..
Country Code
Settings: AUTO, MANUAL, DISABLED
In.AUTO.mode.the.AdderView.CATx.will.at-
tempt.to.query.the.keyboard.attached.to.the.
local.port.to.ascertain.a.country.code..If.a.country.code.is.not.found.then.the.
AdderView.CATx.will.use.the.current.value.of.the.Default.Country.option..In.
MANUAL.mode,.the.connected.local.keyboard.is.not.queried.for.country.infor-
mation.and.instead.the.Default.Country.value.is.reported.to.all.computers.that.
request.country.information..In.DISABLED.mode,.no.country.information.is.sup-
plied.to.computers.requesting.country.information.
Default Country
The.codes.that.may.be.used.within.this.option.are.as.follows:
Country
Code Country Code
Arabic. 01.. Persian.(Farsi).. 20.
Belgian.. 02.. Poland.. 21.
Canadian-Bilingual. 03.. Portugese.. 22.
Canadian-French.. 04.. Russian.. 23.
Czech.Republic.. 05.. Slovakian.. 24.
Danish.. 06.. Spanish.. 25.
Finnish.. 07.. Swedish.. 26.
French.. 08.. Swiss/French.. 27.
German.. 09.. Swiss/German.. 28.
Greek.. 10.. Switzerland.. 29.
Hebrew.. 11.. Taiwan.. 30.
Hungary.. 12.. Turkish-Q.. 31.
International.(ISO).. 13.. UK.. 32.
Italian.. 14.. US.. 33.
Japan.(Katakana).. 15.. Yugoslavia.. 34.
Korean.. 16.. Turkish-F.. 35.
Latin.American.. 17.. Reserved.. 36-255.
Netherlands.. 18.. Not.supported.. 00.
Norwegian.. 19
ADDERVIEW CATx IP
USB Country Code
Country Code AUTO
Default Country 32
Space-Toggle
-Up -Down Esc-Quit
Setup Options
Force Mode
Settings: DISABLED, ENABLED
Available.only.on.non-IP.CATx.units..Force.Mode.allows.an.ADMIN.user.on.port.
1.to.select.which.computers.the.other.user.ports.should.be.switched.to..When.
enabled,.the.ADMIN.user.(on.port.1).can.press.the.TAB.key.to.show.what.user.2.
is.currently.viewing..The.ADMIN.user.can.then.select.an.alternative.computer.for.
user.2..Once.set,.the.ADMIN.user.can.press.the.TAB.key.again.to.move.to.the.
next.user.port.and.so.on.
Alternatively,.the.ADMIN.user.(on.port.1).can.press.CTRL.and.either.1,.2,.3.or.4.
to.show.the.current.video.display.on.any.port.
To.end.Force.mode,.the.ADMIN.user.can,.either:.
•. Press.the.ESC.key
•. Press.TAB.until.user.1.is.shown
•. Press.CTRL.+1