APC UPB60 User Manual
E.2 batteries

Universal Notebook Battery (UPB60) User Manual
Introduction
Thank you for purchasing APC’s Universal Notebook Battery
(model UPB60). Please read the entire user manual prior to
use. Fill out and mail the enclosed Warranty Registration Card,
or register this purchase online at www.apc.com.
APC’s Universal Notebook Battery is a slim and lightweight
external battery pack which provides up to 6-hours of
continuous runtime (actual runtimes may vary by notebook
model and power setting).
Features
• Ultra-lightweight construction reduces bulk and weight in
notebook carry-on luggage.
• Wide range of selectable output voltages power most
notebook computers.
• Four charge/discharge level indicators.
• Letter-coded power tips provided compatibility with most
notebook computers (see Compatibility Guide).
• Compatible with APC’s TravelPower Adapter and Universal
Power Adapter models.
• Up to 70 Watts continuous power, up to 90 Watts peak
power output.
• Up to 6 hours of continuous runtime for your notebook.
Inspection
Check the package contents for the following items:
• APC Universal Notebook Battery (UPB60)
• Input/Output UPB60 Power Cable
• Conversion Plug and Jack Package
• Compatibility Guide
• User’s Manual
• Warranty Card
• Voltage and Tip Label
• Rubber “Feet” (4)
If any item listed above is not in the package, please contact
APC Customer Service at 800-800-4APC for further assistance.
Safety Precautions Please read the following warnings carefully
before using the UPB60 Universal Notebook Battery. Use the
product correctly and according to the procedures described
in this manual.
WARNINGS
• Do not attempt to disassemble or alter any part of this
product.
• Do not store outside of the following temperature range: -4
to 140oF (-20 to 60oC). Do not operate outside of the
following range: 32-104oF (0 to 40oC), as this will damage
or reduce the life of the battery.
• Do not allow this product to have contact with water or
other liquids. If water or other liquids enter the battery
interior, immediately unplug the product from the notebook.
Continued use of the product may result in fire or an electrical
shock.
• Do not place this product near a heat source or expose the
battery to direct flame or heat, as the battery may explode.
Prior to Use
Before using the UPB60 it should be fully charged. Please follow
the instructions below on how to use and maintain the UPB60.
1. Finding the Notebook Voltage Setting
Before using this battery, determine the DC input voltage
requirement for the notebook being used. Notebook voltage
ratings are usually indicated in one of two locations: at the
back of the notebook on the system label or on the notebook
AC-to-DC power adapter label.
If the voltage cannot be located, refer to the “Compatibility
Guide” to determine the required setting for the notebook being
used.
2. Output Voltage Setting
Please refer to Figure 1 to become familiar with all aspects of
the UPB60.
To set the voltage output for the UPB60, proceed as follows:
1. Locate the input voltage requirement for your notebook
computer. (Refer to “Finding the Notebook Voltage Setting”
for instructions).
2. Remove the yellow sticker on the UPB60 which covers the
Output Voltage Selector Switch.
3. Turn the Output Voltage Selector Switch to the required
voltage setting for the notebook being used.
4. Press the "
On/Status" button to make the change effective.
Note: If this is the first time using the battery, attach a power
source to wake up the battery. Continue reading the manual
for further instructions on first use.
3. Changing the Voltage While the Battery is in Use
If the voltage selector dial is moved while the battery is in use,
the battery will interrupt the output of power to your notebook
computer. To resume power output, ensure that the voltage
selector is turned to the correct output voltage (please refer to
the Notebook Users Manual for instructions). Press the
On/
Status push button for approximately 1 second, then release.
The
On/Status indicators will illuminate, indicating the battery
has resumed power output.
4. Charging and Connecting the UPB60
Prior to use, completely charge the UPB60. Follow the
instructions for setting the output voltage on the UPB60.
Provided with the UPB60 is a plastic bag with an assortment
of plug and jack tips. Plug and jack tips are each marked with
a letter designator which corresponds to notebook models listed
in the “Compatibility Guide” and “Compatibility” section of
this manual. Plug tips are used to connect the output power of
the UPB60 to the input DC voltage port on the notebook. Jack
tips are used to connect the UPB60 to a power source
(notebook’s AC/DC Power Adapter, or APC’s TravelPower or
Universal Power Adapters - purchased separately). Tips are
marked with an uppercase letter (A, B, C, etc.). Jacks are
marked with a lowercase letter (a, b, c, etc.).
Example: An IBM® X31 uses plug tip “B” and jack tip “b”. An
Acer Travel Mate® uses plug tip “K” and jack tip “k”, etc. The
letter designators correspond to notebook models listed in the
“Compatibility Guide” and “Compatibility” section of this
manual. To make connections, refer to Figures 1 and 2, then
proceed as follows:
1.
Attach the appropriate Jack tip to the UPB60 Input Power
Connector.
2.
Attach the Plug tip to the UPB60 Output Power Connector.
3.
Attach the notebook power adapter, APC TravelPower
Adapter, or Universal Power Adapter to the UPB60 Jack tip.
4.
The UPB60
Status indicators should illuminate. If they do
not, ensure the notebook power adapter is connected to a
power source, and any switch controlling the power source
is in the
ON position.
5.
When the
Status indicators illuminate, the UPB60 is
charging. Continue charging the UPB60 until all indicators
illuminate and then extinguish.
E.2
Batteries