Sony MDR-EX10LP - Manual

Stereo
Headphones
MDR-EX10LP
4-421-872-11(1)
Operating Instructions
Manual de instrucciones
English
Stereo headphones
Features
 400 kJ/m 3 high power neodymium magnets produce high-resolution treble and
midrange with powerful bass
 Hybrid silicone rubber earbuds (S, M, L) supplied for secure fitting and long-term
wearing comfort
 Y-type cord with cord slider to prevent cord tangling
 Convenient cord adjuster supplied
How to use (see fig. )
Connect the headphones to a device with the stereo mini jack.
Wear the earpiece marked  in your right ear and the one marked  in your left ear.
There is a tactile dot on the unit marked  to distinguish the left side.
Using the cord slider (see fig. -)
Move up and down to change the split position of the cord.
Installing the earbuds correctly (see fig. )
If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoy
better sound quality, change the earbuds to another size, or adjust the earbuds position to
sit on your ears comfortably and fit your ears snugly.
If the earbuds do not fit your ears, try another size. When you change the earbuds, install
them firmly on the headphones to prevent the earbud from detaching and remaining in
your ear.
To check the transparent earbud sizes
The transparent earbud sizes are distinguished by a line pattern (see fig. -).
To check the black earbud sizes
The black earbud sizes are distinguished by the inside color (see fig. -).
Black earbud sizes (inside color)
Small

Large

S
(Orange)
M
(Green)
L
(Light blue)
To detach an earbud (see fig. -)
While holding the headphone, twist and pull the earbud off.
 Tip
If the earbud slips and cannot be detached, wrap it in a dry soft cloth.
To attach an earbud (see fig. -)
Push the parts inside of the earbud into the headphone until the projecting part of the
headphone is fully covered.
To clean the earbuds
Remove the earbuds from the headphones, and wash them with a mild detergent solution.
Specifications
Type: Closed, dynamic
Driver unit: 9 mm, dome type (CCAW)
Power handling capacity: 100 mW (IEC*)
Impedance: 16 Ω at 1 kHz
Sensitivity: 100 dB/mW
Frequency response: 8 – 22,000 Hz
Cord: Approx. 1.2 m (47 1 /
4
in), Litz cord Y-type
Plug: L-shaped stereo mini plug
Mass: Approx. 3 g (0.11 oz) (without cord)
Supplied accessories
Earbuds S (2), M (2), L (2)
Card warranty (1)
Operating Instructions (1)
* IEC = International Electrotechnical Commission
Design and specifications are subject to change without notice.
Precautions
 Please keep your headphones clean at all times especially inside the rubber earbud.
(see fig. )
If any dust or ear wax is inside the earbud, you may experience some listening
difficulties.
 Listening with headphones at high volume may affect your hearing. For traffic safety,
do not use while driving or cycling.
 The earbuds may deteriorate due to long-term storage or use.
 Install the earbuds firmly onto the headphones. If an earbud accidentally detaches and
is left in your ear, it may cause injury.
Note on static electricity
In particularly dry air conditions, mild tingling may be felt on your ears. This is a result
of static electricity accumulated in the body, and not a malfunction of the headphones.
The effect can be minimized by wearing clothes made from natural materials.
Optional replacement earbuds can be ordered from your nearest Sony dealer.
©2010 Sony Corporation Printed in China


L-shaped
stereo mini plug
Approx. 1.2 m

Sectional View
Colored parts


 
S
2 lines
M
3 lines
L
4 lines
