AMX MODERO VIEWPOINT WIDESCREEN TOUCH PANEL MVP-5200I - Manual (Page 126)

Programming
118 MVP-5200i Modero Viewpoint Widescreen Touch Panel
"^" Button Commands (Cont.)
^BMF
Set any/all button
parameters by
sending
embedded codes
and data.
Syntax:
"'^BMF-,,'"Variables: variable text address char array = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons 1 = Off state and 2 = On state).
level range = 1 - 600 (level value is 1 - 65535).
data:
’%B’ = Set the border style name. See the Border Styles and
Programming Numbers table on page 110.
’%B’, = Set the borer style number. See the Border Styles and
Programming Numbers table on page 110.
’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
Refer to the ^BDO command on page 115 for more information.
’%F’, = Set the font. See the Default Font Styles and ID
Numbers table on page 109.
’%F’ = Set the font. See the Default Font Styles and ID
Numbers table on page 109.
’%MI’ = Set the mask image. Refer to the ^BMI command on page 120 for
more information.
’%T’ = Set the text using ASCII characters (empty is clear).
’%P’ = Set the picture/bitmap filename (empty is clear).
’%I’,’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%I’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%J’, = As shown the following telephone keypad alignment
chart:’%JT’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
’%JB’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,,’
’%JI’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’14
78963250Zero can be used for an absolute position
Variables:
variable text address char array = 1 - 4000.
button states range = 1 - 256 for multi-state buttons (0 = All states, for General buttons
1 = Off state and 2 = On state).
level range = 1 - 600 (level value is 1 - 65535).
data:
’%B’ = Set the border style name. See the Border Styles and
Programming Numbers table on page 110.
’%B’, = Set the borer style number. See the Border Styles and
Programming Numbers table on page 110.
’%DO<1-5><1-5><1-5><1-5><1-5> = Set the draw order. Listed from bottom to top.
Refer to the ^BDO command on page 115 for more information.
’%F’, = Set the font. See the Default Font Styles and ID
Numbers table on page 109.
’%F’ = Set the font. See the Default Font Styles and ID
Numbers table on page 109.
’%MI’ = Set the mask image. Refer to the ^BMI command on page 120 for
more information.
’%T’ = Set the text using ASCII characters (empty is clear).
’%P’ = Set the picture/bitmap filename (empty is clear).
’%I’,’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%I’ = Set the icon using values of 01 - 9900 (icon numbers are
assigned in the TPDesign4 Resource Manager tab - Slots section).
’%J’, = As shown the following telephone keypad alignment
chart:
’%JT’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
’%JB’ = As shown the above telephone keypad
alignment chart BUT the 0 (zero) is absolute and followed by ’,,’
’%JI’ = As shown the above telephone keypad alignment chart,
BUT the 0 (zero) is absolute and followed by ’,,’
1
4
7
8 9
6
3 2
5
0
Zero can be used for an absolute position