beautypg.com

Fcc information, Caution, Declaration of conformity – Spektrum SPMAR9000 User Manual

Page 2: Questions, assistance, and repairs, Inspection or repairs, Warranty inspection and repairs, Non-warranty repairs, Warranty period, Limited warranty, Damage limits

background image

Tips on Using Spektrum 2.4GHz
ModelMatch

Some Spektrum and JR transmitters offer a patent pending feature called ModelMatch. ModelMatch

prevents the possibility of operating a model using the wrong model memory, potentially preventing a

crash. With ModelMatch each model memory has its own unique code (GUID) and during the binding

process the code is programmed into the receiver. Later, when the system is turned on, the receiver will

only connect to the transmitter if the corresponding model memory is programmed on screen.
Note: If at any time you turn on the system and it fails to connect, check to be sure the correct

model memory is selected in the transmitter. Please note that the DX5e and Aircraft Modules do

not have ModelMatch.

While your DSM equipped 2.4GHz system is intuitive to operate, functioning nearly identically to

72MHz systems, following are a few common questions from customers.
1. Q: Which do I turn on first, the transmitter or the receiver?

A: If the receiver is turned off first —all servos except for the throttle will be driven to their preset

failsafe positions set during binding. At this time the throttle channel doesn’t output a pulse

position preventing the arming of electronic speed controllers or in the case of an engine

powered aircraft the throttle servo remains in its current position. When the transmitter is

then turned on the transmitter scans the 2.4GHz band and acquires two open channels. Then

the receiver that was previously bound to the transmitter scans the band and finds the GUID

(Globally Unique Identifier code) stored during binding. The system then connects and

operates normally.

If the transmitter is turned on first—the transmitter scans the 2.4GHz band and acquires two

open channels. When the receiver is then turned on for a short period (the time it takes to

connect) all servos except for the throttle are driven to their preset failsafe positions while the

throttle has no output pulse. The receiver scans the 2.4GHz band looking for the previously

stored GUID and when it locates the specific GUID code and confirms uncorrupted repeatable

packet information, the system connects and normal operation takes place. Typically this takes

2 to 6 seconds.

2. Q: Sometimes the system takes longer to connect and sometimes it doesn’t connect

at all?

A: In order for the system to connect (after the receiver is bound) the receiver must receive a large

number of consecutive uninterrupted perfect packets from the transmitter in order to connect.

This process is purposely critical of the environment ensuring that it’s safe to fly when the system

does connect. If the transmitter is too close to the receiver (less than 4 ft.) or if the transmitter

is located near metal objects (metal TX case, the bed of a truck, the top of a metal work bench,

etc.) connection will take longer and in some cases connection will not occur as the system is

receiving reflected 2.4GHz energy from itself and is interpreting this as unfriendly noise. Moving

the system away from metal objects or moving the transmitter away from the receiver and

powering the system again will cause a connection to occur. This only happens during the initial

connection. Once connected the system is locked in and should a loss of signal occur (failsafe)

the system connects immediately (4ms) when signal is regained.

3. Q: I’ve heard that the DSM system is less tolerant of low voltage. Is this correct?

A: All DSM receivers have an operational voltage range of 3.5 to 9.6 volts. With most systems this

is not a problem as in fact most servos cease to operate at around 3.8 volts. When using multiple

high-current draw servos with a single or inadequate battery/power source, heavy momentary

loads can cause the voltage to dip below this 3.5-volt threshold thus causing the entire system

(servos and receiver) to brown out. When the voltage drops below the low voltage threshold

(3.5 volts), the DSM receiver must reboot (go through the startup process of scanning the band

and finding the transmitter) and this can take several seconds. Please read the receiver power

requirement section as this explains how to test for and prevent this occurrence.

4. Q: Sometimes my receiver loses its bind and won’t connect requiring rebinding.

What happens if the bind is lost in flight?

A: The receiver will never lose its bind unless it’s instructed to. It’s important to understand that

during the binding process the receiver not only learns the GUID (code) of the transmitter but

the transmitter learns and stores the type of receiver that it’s bound to. If the transmitter is placed

into bind mode, the transmitter looks for the binding protocol signal from a receiver. If no signal

is present, the transmitter no longer has the correct information to connect to a specific receiver

and in essence the transmitter has been “unbound” from the receiver. We’ve had several DX7

customers that use transmitter stands or trays that unknowingly depress the bind button and the

system is then turned on losing the necessary information to allow the connection to take place.

We’ve also had DX7 customers that didn’t fully understand the range test process and pushed the

bind button before turning on the transmitter also causing the system to “lose its bind.”

Age Recommendation: 14 years or over. This is not a toy. This product is not intended for use by

children without direct adult supervision.

Revised 11/08 10653.1

How QuickConnect With Brownout Detection Works
• When the receiver voltage drops below 3.5 volts the system drops out (ceases to operate).

• When power is restored the receiver immediately attempts to reconnect to the last two frequencies

that it was connected to.

• If the two frequencies are present (the transmitter was left on) the system reconnects typically about

4/100 of a second.

QuickConnect with Brownout Detection is designed to allow you to fly safely through most short

duration power interruptions, however, the root cause of these interruptions must be corrected before

the next flight to prevent a crash.
Note: If a brownout occurs in flight it is vital that the cause of the brownout be determined and corrected.

Flight Log (SPM9540 Optional)
The Flight Log is compatible with the AR9000. The Flight Log displays overall RF link performance as

well as the individual internal and external receiver link data. Additionally it displays receiver voltage.

Using the Flight Log
After a flight and before turning off the receiver or transmitter, plug the Flight Log into the Data port on

the AR9000. The screen will automatically display voltage e.g. 6v2= 6.2 volts.
Note: When the voltage reaches 4.8 volts or less, the screen will flash indicating low voltage.
Press the button to display the following information:

A – Antenna fades on internal antenna A

B – Antenna fades on internal antenna B

L – Antenna fades on the left external antenna

R – Antenna fades on the right external antenna

F – Frame loss

H – Holds

Note: – – – (three dashed lines) will appear if the antenna is not attached
Antenna fades—represents the loss of a bit of information on that specific antenna.

Typically it’s normal to have as many as 50 to 100 antenna fades during a flight. If any single antenna

experiences over 500 fades in a single flight, the antenna should be repositioned in the aircraft to

optimize the RF link.
Frame loss—represents simultaneous antenna fades on all attached receivers.

If the RF link is performing optimally, frame losses per flight should be less than 20. A hold occurs

when 45 consecutive frame losses occur. This takes about one second. If a hold occurs during a flight,

it’s important to evaluate the system, moving the antennas to different locations and or checking to be

sure the transmitter and receivers are all working correctly.
Note: A servo extension can be used to allow the Flight Log to be plugged in more conveniently.

On some models, the Flight Log can be plugged in, attached and left on the model using

double-sided tape. Mounting the Flight Log conveniently to the side frame is common with

helicopters.

FCC Information

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Caution:

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found

to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to

2.4835GHz frequency range.

Declaration of Conformity

(in accordance with ISO/IEC 17050-1)

No. HH20081023

Product(s):

AR9000 Receiver

Item Number(s):

SPMAR9000

The object of declaration described above is in conformity with the requirements of the specifica-

tions listed below, following the provisions of the European R&TTE directive 1999/5/EC:

EN 300-328, v1.7.1 ERM requirements for wideband transmission systems

operating in the 2.4 GHz ISM band

EN 301 489-1 v.1.6.1 General EMC requirements for Radio equipment

EN 301 489-17 v.1.2.1
Signed for and on behalf of:

Horizon Hobby, Inc.

Champaign, IL USA

Oct. 23, 2008

Steven A. Hall

Vice President

International Operations and Risk Management

Horizon Hobby, Inc.

© 2008 Horizon Hobby, Inc. Spektrum radios and accessories are distributed exclusively by Horizon Hobby, Inc.

4105 Fieldstone Road, Champaign, IL 61822 Call toll-free, 877-504-0233.
DSM and DSM2 are trademarks or registered trademarks of Horizon Hobby, Inc.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.
US patent number 7,391,320. Other patents pending.

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once assembly,

setup or use of the Product has been started, you must contact Horizon directly. This will enable Horizon to

better answer your questions and service you in the event that you may need any assistance. For questions

or assistance, please direct your email to [email protected], or call 877.504.0233 toll

free to speak to the Product Support department.

Inspection or Repairs

If this Product needs to be inspected or repaired, please call for a Return Merchandise Authorization (RMA).

Pack the Product securely using a shipping carton. Please note that original boxes may be included, but

are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that

provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise

until it arrives and is accepted at our facility. A Service Repair Request is available at www.horizonhobby.

com on the “Support” tab. If you do not have internet access, please include a letter with your complete

name, street address, email address and phone number where you can be reached during business days,

your RMA number, a list of the included items, method of payment for any non-warranty expenses and a

brief summary of the problem. Your original sales receipt must also be included for warranty consideration.

Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

Warranty Inspection and Repairs

To receive warranty service, you must include your original sales receipt verifying the proof-of-purchase

date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge.

Repair or replacement decisions are at the sole discretion of Horizon Hobby.

Non-Warranty Repairs

Should your repair not be covered by warranty the repair will be completed and payment will be required

without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost.

By submitting the item for repair you are agreeing to payment of the repair without notification. Repair

estimates are available upon request. You must include this request with your repair. Non-warranty repair

estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight.

Please advise us of your preferred method of payment. Horizon accepts money orders and cashiers checks,

as well as Visa, MasterCard, American Express, and Discover cards. If you choose to pay by credit card,

please include your credit card number and expiration date. Any repair left unpaid or unclaimed after 90

days will be considered abandoned and will be disposed of accordingly. Please note: non-warranty repair is

only available on electronics and model engines.
Electronics and engines requiring inspection or repair should be shipped to the following address:

Horizon Service Center

4105 Fieldstone Road

Champaign, Illinois 61822

All other Products requiring warranty inspection or repair should be shipped to the following address:

Horizon Product Support

4105 Fieldstone Road

Champaign, Illinois 61822

Please call 877-504-0233 or e-mail us at [email protected] with any questions or
concerns regarding this product or warranty.

European Union:

Electronics and engines requiring inspection or repair should be shipped to one of the following addresses:

Warranty Period

Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”)

will be free from defects in materials and workmanship for a period of 1 year from the date of purchase by

the Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser (“Purchaser”) and is not transferable. REPAIR OR

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE

PURCHASER. This warranty covers only those Products purchased from an authorized Horizon dealer.

Third party transactions are not covered by this warranty. Proof of purchase is required for warranty claims.

Further, Horizon reserves the right to change or modify this warranty without notice and disclaims all other

warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED,

ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE

PRODUCT. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE

PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon will, at its option, (i)

repair or (ii) replace, any Product determined by Horizon to be defective. In the event of a defect, these are

the Purchaser’s exclusive remedies. Horizon reserves the right to inspect any and all equipment involved

in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon. This warranty

does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence,

commercial use, or modification of or to any part of the Product. This warranty does not cover damage due

to improper installation, operation, maintenance, or attempted repair by anyone other than Horizon. Return

of any goods by Purchaser must be approved in writing by Horizon before shipment.

Damage Limits

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.

Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability

is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability

shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the

user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product,

you are advised to return this Product immediately in new and unused condition to the place of purchase.
Law: These Terms are governed by Illinois law (without regard to conflict of law principals).

Safety Precautions

This is a sophisticated hobby Product and not a toy. It must be operated with caution and common sense

and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible

manner could result in injury or damage to the Product or other property. This Product is not intended

for use by children without direct adult supervision. The Product manual contains instructions for safety,

operation and maintenance. It is essential to read and follow all the instructions and warnings in the

manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or injury.

Horizon Hobby UK

Units 1-4 Ployters Rd

Staple Tye, Harlow

Essex CM18 7NS

United Kingdom

Please call +44 (0) 1279 641 097 or email [email protected]

with any questions or concerns regarding this product or warranty.

Horizon Technischer Service

Hamburger Str. 10

25335 Elmshorn

Germany

Please call +49 4121 46199 66 or email [email protected]

with any questions or concerns regarding this product or warranty.

Instructions for Disposal of WEEE by Users in the

European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility

to dispose of their waste equipment by handing it over to a designated collection point for the

recycling of waste electrical and electronic equipment. The separate collection and recycling of your

waste equipment at the time of disposal will help to conserve natural resources and ensure that it is

recycled in a manner that protects human health and the environment. For more information about

where you can drop off your waste equipment for recycling, please contact your local city office,

your household waste disposal service or where you purchased the product.