beautypg.com

ADTRAN 1224 User Manual

ADTRAN Computer Accessories

background image

Quick Start Guide, 61200500E1-13C, November 2006

Copyright © 2006 ADTRAN, All Rights Reserved

For more detailed documentation, visit us online at

www.adtran.com

.

Quick Start Guide

®

NetVanta 1224 Series Switches

P/N 1200500E1/L1, 1200504E1/L1, 1200510L1,

1200520E1/L1, 1200590L1

N

ET

V

ANTA

1224 F

RONT

P

ANEL

L

AYOUT

N

ET

V

ANTA

1224STR F

RONT

P

ANEL

L

AYOUT

N

ET

V

ANTA

1224ST F

RONT

P

ANEL

L

AYOUT

N

ET

V

ANTA

1224

AND

1224ST R

EAR

P

ANEL

L

AYOUT

N

ET

V

ANTA

1224R

AND

1224STR (AC

VERSION

) R

EAR

P

ANEL

L

AYOUT

G

ETTING

S

TARTED

Two configuration methods are available for your NetVanta switch:

Web-based GUI

AOS Command Line Interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations
for each setting. However, using the AOS CLI may be necessary for more advanced
configurations.

A

CCESS

THE

GUI

You may access the web-based GUI from any web browser on your network by following these
steps:

1.

Connect the switch to your PC using any of the 24 Ethernet ports on the front of the unit.

2.

Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address,
you will need to change the unit’s IP address using the CLI. (Refer to the next two sections
for instructions.)

3.

Enter the unit’s IP address in your browser address line. The default IP address is
10.10.10.1.

4.

You will then be prompted for the username and password (the default settings are admin
and password).

5.

The initial GUI screen appears.

A

CCESS

THE

CLI

Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the
NetVanta switch CONSOLE port, you need the following items:

VT100 terminal or PC (with VT100 terminal emulation software)

Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate
interface for your terminal or PC communication port on the other end

1.

Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear
panel of the unit.

2.

Connect the other end of the serial cable to the terminal or PC.

3.

Provide power to the unit as appropriate. Refer to the NetVanta 1000 and NetVanta 1000R
Series Hardware Installation Guide
(provided on the ADTRAN OS System Documentation
CD) for more details.

4.

Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press to activate the AOS CLI.

5.

Enter enable at the > prompt.

6.

Enter the enable password when prompted. The default password is password.

The configuration parameters used in the examples outlined in this
document are for instructional purposes only. Please replace all
underlined entries (

example

) with your specific parameters to configure

your application.

N

ET

V

ANTA

1224R F

RONT

P

ANEL

L

AYOUT

N

ET

V

ANTA

1224STR (DC

VERSION

) R

EAR

P

ANEL

L

AYOUT

-48V....., 1.2A

+24V....., 2.5A

USE COPPER

CONDUCTORS ONLY