Listening through a receiver, Check points before requesting service – Samsung PS50A551S3R User Manual
Page 42
English - 4
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select
Input, then press the ENTER button.
Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER
button.
Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
4 Press the ◄ or ► button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
5 Press the EXIT button to exit.
➢
When the receiver is set to On, you can listen to the TV sound through the 2-channel
receiver.
➢
If the receiver is exclusively for a home theater only (supporting audio only), it may
not appear in the device list.
➢
In case of a content with copyright problems, listening through the receiver may not
properly operate.
➢
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or
a power failure), the
TV Speaker may be set to Off when you turn the TV on again. (see page 23)
Check Points before Requesting Service
Symptom
Solution
Anynet+ does not work.
■ Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI 1.3 cable, please make
sure to search devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.
■ Check if the Anynet+ device is properly connected to the TV and
check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup
menu.
■ Press the
TV button on the TV remote control to switch to TV. Then
press the
TOOLS button to show the Anynet+ menu and select a
menu you want.
I want to exit Anynet+.
■ Select
View TV in Anynet+ menu.
■ Press the
SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■ Press any of
CH, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet+ device is not connected.)
The message Connecting to
Anynet+ device… appears on
the screen.
■ You cannot use the remote control when you are configuring
Anynet+ or switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to
view mode is complete.
The Anynet+ device does not
play.
■ You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI 1.3 cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI 1.3 cable only.
Some HDMI cables may not support Anynet+ functions.
The TV programme cannot be
recorded.
■ Check whether the antenna jack on the recording device is properly
connected.
Enter
Move
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver
:On
Setup
TV P 1
Exit
BN68-01434A-Eng.indb 42
2008-03-10 오후 3:31:22