Samsung HPT4264X-XAA - Manual (Page 19)

English - 19
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (air) and cable channels. After the
available channels are memorized, use the CH or CH button to scan through the channels. This eliminates
the need to change channels by entering the channel digits. There are three steps for memorizing channels:
selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must
specify the type of signal source that is connected to the TV (i.e. an air or a cable
system).
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ENTER button select Antenna.
Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
Press the EXIT button to exit.
Storing Channels in Memory (Automatic Method)
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ▲ or ▼ button to select Auto Program, then press the ENTER
button.
3 Press the ▲ or ▼ button to select the antenna connection, then press the
ENTER button.
➢ Air: “Air” antenna signal.
Cable: “Cable” antenna signal.
Air+Cable: “Air” and “Cable” antenna signals.
➢ If the antenna is connected to ANT 2 IN (CABLE), select Cable and if it is
connected to ANT 1 IN (AIR), select Air.
➢ If both ANT 1 IN and ANT 2 IN are connected, select the Air + Cable.
➢ If you selected Air, then go to step 5.
4 Press the ▲ or ▼ to select the correct analog signal cable system source from
among STD, HRC, and IRC, then press the ENTER button. If you have Digital
cable TV, select the cable system signal source for both Analog and Digital.
➢ If you have Digital cable TV, select the signal source for both Analog and
Digital.
➢ STD, HRC, and IRC identify various types of cable TV systems. Contact
your local cable company to identify the type of cable system that exists in
your particular area. At this point the signal source has been selected.
5 The TV begins memorizing all available stations.
If you want to stop Auto Programming, press the ENTER button. The Stop
Auto Program? message will be displayed. Select Yes by pressing the ◄ or ►
button.
Press the EXIT button to exit.
➢ The TV must be connected to antenna/cable in order to receive digital TV
signals. Even if a particular channel is deleted from the memory, you can
always tune to that channel directly by using the number buttons on the
remote control.
➢ • All available DTV and analog channels are automatically stored in
memory.
• It takes approximately 3 to 10 minutes to memorize channels.
Auto Program
Auto Program in progress.
Cable Channel 67
68 %
Stop
Enter
Antenna : Air ►
Auto Program ►
Clear Scrambled Channel ►
Channel List ►
Name ►
Fine Tune ►
Signal Strength ►
LNA : On ►
Channel T V
Enter Move
Auto Program T V
Select the antennas to memorize.
Air
Cable
Air + Cable Start
Enter Move
Start
Start
Auto Program
Stop Auto Program?
Yes No
68 %
Antenna : Air ►
Auto Program ►
Clear Scrambled Channel ►
Channel List ►
Name ►
Fine Tune ►
Signal Strength ►
LNA : On ►
Channel T V
Enter Move Return
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
LNA : On
Channel T V
Enter Move
Air
Cable
Return
Return
Return
Select the cable system.
Auto Program T V
Enter Move Return
STD
HRC
IRC
Analog
STD
HRC
IRC
Digital
Start
Return
Enter Move Return
BN68-01131N-02Eng-1.indd 19 2007-02-27 ш¿¿¸ 11:13:16