Campbell Scientific Enclosure Supply Kit (Part #7363) - Manual

ENCLOSURE SUPPLY KIT (Part #7363)
The contents of this bag are for use with
Campbell Scientific’s field enclosures. Please
note that some of the enclosed items should be
saved for future use.
Printed 1/23/2013
1. Use the #6 screws and plastic grommets to
mount additional peripherals to the enclosure
backplate. Dataloggers, power supplies, and
most peripherals are either attached to the
backplate prior to shipment from the factory
or are supplied with additional screws and
grommets. To insert the grommet, push the
points of the flanges into the center of any
square hole. To remove a grommet without
damage, remove the enclosure backplate
and use pliers to pinch the grommet flanges
together.
2. If desired, insert the 25745 PVC coupling to
reduce the conduit’s diameter to 0.5-in.
Route the sensor leads through the
enclosure conduit to the datalogger or
peripheral terminal strips.
3. Use the cable-tie tabs and 8-in cable ties to
strain relief the cables to the side of the
enclosure as shown.
NOTE: The adhesive of the cable tie tab may not
stick during extremely cold temperatures or
extremely high humidity. In these situations,
fasten the cable-tie tab to the backplate using a
#6 screw and grommet.
4. Strain relief the sensor leads to the
datalogger’s strain-relief flanges with the 4-in
cable ties.
5. Remove the backing tape from the humidity
indicator and attach to the side of the
enclosure as shown.
6. Seal the gap between the sensor leads and
the enclosure conduit with sealing putty.
7. Place two desiccant packs inside the
enclosure; reseal the other two inside the
plastic bag. Store the extra packs in a dry
area and use them to replace the two in the
enclosure during a site visit or when the 40%
ring on the humidity indicator turns pink.
CAUTION: We recommend purchasing new
desiccant instead of oven drying, which is messy
and time consuming.
DO NOT EAT
UNITED DESICCANTS-GATES
101CHRISTINE, BELEN, NEW MEXICO 87002
DESI PAK
SPECIFICATION MIL-D-3464 TYPE I &II
REACTIVATION TIME IN-BAG 16 HOURS AT 250 F
DESICCANT
ACTIVATED
BAGGED FOR
CONTENTS
4
UNITS
PACKAGE USE
AND STATIC
DEHUMIDIFICATION
DO NOT EAT
UNITED DESICCANTS-GATES
101CHRISTINE, BELEN, NEW MEXICO 87002
DESI PAK
SPECIFICATION MIL-D-3464 TYPE I &II
REACTIVATION TIME IN-BAG 16 HOURS AT 250 F
DESICCANT
ACTIVATED
BAGGED FOR
CONTENTS
4
UNITS
PACKAGE USE
AND STATIC
DEHUMIDIFICATION
INDICATOR HUMIDITY
MS20003-2
EXAMINE
ITEM
IF PINK
CHANGE
DESICCANT
IF PINK
WARNING
IF PINK
AVOID METAL CONTACT
DISCARD IF CIRCLES OVERRUN
Humidial Corp., Colton Calif.
Screwdriver
PVC Coupling
8” Cable Tie
4” Cable Tie Cable Tie Tab
#6 Screws
Grommets
Putty
Humidity Indicator Card
Desiccant Pack
Cable-Tie Tab 4-in Cable Tie
8-in Cable Tie
PVC Coupling
Screwdriver
Desiccant Pack
Humidity Indicator Card
Putty
Grommets
#6 Screws
The contents of the enclosure supply kit are the following.
Qty. Part # Description
8 505 #6-32 x .375” screws
8 6044 grommets
4 2376 3-cm cable-tie tabs
6 2207 4-in cable ties
6 4005 8-in cable ties
1 28878 humidity indicator card
2 6596 4-oz container of sealing putty
4 4905 4-unit desiccant packs
1 6290 Phillips screwdriver
1 25745 PVC coupling
thia ia
tryu to read this whoever
thia ia thia thia
thia thia thia thia
thia thia
thia thia thia thia
thia thia
thia thia thia thia
thia thia
thia thia thia thia
thia thia thia thia thia thia
thia thia
DESI PAK.
DESI PAK.
DESI PAK.
SPECIF ICATIO N MIL-D -3463 KALDH FI;O AK JI AI AJ HFHO A LDLIFJ ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD
SPECIFICATION MIL-D-3463 KALDHFI;O AKJI AI AJHFHO ALDLIFJ ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD
DO N OT EA T UNITED DESICCANTS-GATES
UNITED DESICCANTS-GATES
DO N OT E AT UNITE D DES ICCAN TS-G ATES
UN ITE D D ES IC CA NTS -G ATE S
DESI PAK.
DESI PAK.
DESI PAK.
SPECIF ICATIO N MIL-D -3463 KALDH FI;O AK JI AI AJ HFHO A LDLIFJ ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD ASLFJO AKD
SPECIFICATION MIL-D-3463 KALDHFI;O AKJI AI AJHFHO ALDLIFJ ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD ASLFJ O AKD
DO N OT EA T UNITED DESICCANTS-GATES UNITED DESICCANTS-GATES
DO N OT E AT UNITED DESIC
CAN TS-G ATES
UN ITE D D ES IC CA NTS -G ATE S
PS12 POWER SUPPLY
WITH 12V CHARGING REGULATOR
MADE IN USA
WARNING:
PERMANENT DAMAGE TO RECHARGEABLE
CELLS MAY RESULT IF DISCHARGED
BELOW 10.5 VOLTS
FUNCTION
INT
EXT BAT
CHG OFF ON CHG CHG +12 +12
PS12 BATTERY
EXTERNAL BATTERY - DO NOT USE WITH
INTERNAL RECHARGEABLE BATTERY
CHARGE VOLTAGE PRESENT
INPUT FROM CHARGER OR SOLAR PANEL
16-26 VDC OR AC RMS: POSITIVE TO
EITHER TERMINAL, NEGATIVE TO OTHER
POWER TO DATALOGGER OR
12V PERIPHERALS
SE
DIFF G G H L 1 2 1 AG H L AG H L AG E1 AG E2 G 3 4 2 5 6 3
SE
DIFF G G H L 7 8 4 AG H L AG H L AG E3 AG G G 9 10 5 11 12 6
P1 G P2 G C8 C7 C6 C5 C4 C3 C2 C1 G 12V 12V SDM
5V 5V G G SW 12V SW 12V CTRL
Logan, Utah
G 12V
G 12V
POWER IN
CR10X WIRING PANEL MADE IN USA
WIRING PANEL NO.
EARTH GROUND
CS I/O
4-in Cable Ties
Humidity
Indicator
8-in Cable Ties
and Tabs
Desiccant
Packs
Grommets and screws
hold peripherals to
enclosure backplate
Sealing Putty