ASKO W6441 - Manual (Page 19)

Page 19
To change the language, follow the steps below:
1. Turn the machine off then on again.
2. Press ENTER five times in succession then press
P1 five times. (This must be done within 15 seconds.)
3. When the Language menu displays, press to
advance to the desired language.
4. When your preference displays, press
ENTER
.
CHANGING THE TEMPERATURE
READOUT ON THE LCD WINDOW
FROM CELSIUS TO FAHRENHEIT
You can change the temperature readout on the LCD
window from Celsius to Fahrenheit and vice versa. To
do this follow the steps below:
1. Turn the machine off then on again.
2. Press
ENTER
five times in succession then press
P2 five times. (This must be done within 15 seconds.)
3. When the Temperature menu displays, press an
Arrow
button to toggle between Fahrenheit and
Celsius.
4. When your preference displays, press ENTER .
CHILD-SAFE START BUTTON
As a safety measure, you can program Model W6761
not to start unless the Start button is held down for three
seconds. To do this, follow the steps below:
1. Turn the machine off then on.
2. Press ENTER five times, then press P3 five times.
(This must be done within 15 seconds.)
3. “Delayed start” displays with “0” flashing in the lower
right corner. Press the right Arrow button to toggle
the display to “3.”
4. Press ENTER .
CHILD-SAFE MENU BUTTON
Please note that when you set the child-safe Start button,
the Menu button is automatically programmed to delay
for three seconds before it becomes active. This prevents
a child from accidentally changing the program settings.
When you want to change a program, press the Menu
button for three seconds to activate the menus. The
Menu button will work normally (without the 3-second
delay) until you have completed your changes. If it is
not pressed for two minutes, it will automatically revert
back to the child-safe mode.
Delayed Start
This lets you set a delayed start from 1 to 24 hours.
This means you can set the washer to start at the most
convenient time for you, such as an hour before you
arrive home from work. This feature is also useful in
areas where utility companies offer discount rates during
off-peak hours.
1. Press MENU until “Select time for delayed start”
displays.
2. Use the Arrow buttons to increase or decrease the
delay time. (The numbers indicate hours.)
3. When the number of hours you want to delay starting
the machine displays, press
ENTER
. The LCD will
display the delay start time.
4. If you only want to use this setting temporarily (for
this one load), press START . When the program
ends it will revert back to the previous setting.
5. If you want to save this setting permanently, press
ENTER
again then press
START
. The program will
retain the change.
Selecting Options
This lets you select Super Rinse, ECO (Economy), Pre-
soak, Anti-crease, or High Water Level.
1. Press MENU until “Select options” displays.
2. Continue to press MENU to scroll through the
options.
3. When the option you wish to select displays, press
an Arrow to toggle between Off and On.
4. Press ENTER . The LCD will display the new setting.
5. If you only want to use this setting temporarily (for
this one load), press
START
. When the program
ends it will revert back to the previous setting.
6. If you want to save this setting permanently, press
ENTER again then press START . The program will
retain the change.
RESTORING A PRESET
PROGRAM
To restore a preset program to its factory default settings,
simply press the button for the preset program you want
to restore and hold it down while your press
ENTER .
The program will revert to its factory default settings.
NOTE: If you change the P3 program then decide to
restore its factory default settings, after
pressing P3 and ENTER, you must go into the
Options menu (see “Selecting Options” above)
and turn off Short Spin.
♦
English
♦
French
♦
Spanish
♦
Portuguese
♦
Italian
♦
German
♦
Swedish
♦
Danish
♦
Norwegian
♦
Netherlands
♦
Finnish
CHANGING THE LANGUAGE ON
THE LCD WINDOW
There are eleven languages available for the LCD
window: