Ag-Bag G6070P - Manual (Page 90)

Capscrew, Hex Hd. 5/16-18 x 3/4 in. Gr 5....31
CARDANTube.....63
Chain, #40-2, 16 Pitches w/ Connector.....22,
25
Chain, #50 Riveted, 66P, 41 in. Long
UST.....71
Chain, Conveyor Complete (G6060 & PB6000
Only).....31
Chain, Conveyor, Long w/Weld On Flight....25
Chain, Long w/Weld On Flight.....21
Chain, Roller, #120-2 59P - G6060 & PB6000
Only.....17
Chain, Roller, #120-2, 7.875 Ft, 63 P, UST -
G6070 Only.....17
Chain, Roller, #50, 114 Pitches.....21, 25
Chain, Safety.....77
Check Valve.....81
Clamp, 1-1/2 in. Vinyl.....67
Clamp, 1-1/2 in. Vinyl - G6070 & G6070P...41
Clamp, Cable (G6060 & PB6000 Only).....31
Clamp, Cable, 1/4 in......37
Clamp, Hose, .625 ID Double - G6070 &
G6070P.....41
Clamp, Hose, .625 in. I.D. Double.....81
Clamp, Single, .63 ID.....51
Clamp, Single, .63 in. ID.....22
Clamp, Vinyl, .38 Dia......51
Clean Out Door w/Decals.....29
Clevis.....77
Clip, Hydraulic Line.....39, 67
Complete Shield Kit.....63
Cone, Roller Bearing, 1-1/4 in......13
Cone, Roller Bearing, 1-5/8 in......13
Connector, 06 MJIC x 10 ORB.....68
Connector, 37° ORB 7/8-14.....68
Connector, Male, 3/8 in. JIC x 1/4 in. NPT...39
Connector, Male, 3/8 JIC x 1/2 NPT.....68
Connector, Male, JIC - NPT, 3/8 in. x 3/8
in......39
Conveyor Adjuster End Weldment.....22
Conveyor Complete (Used On G6060 &
PB6000 Only).....32
Conveyor End, Adjusting w/Decals (G6060 &
PB6000 Only).....31
Conveyor Lower Assembly - Not Serviced
Separately Refer to Lower Assembly Split
Conveyor Page for Parts Breakdown.....25
Conveyor Roller, 1.250 in. Bore.....29
Conveyor, Frame w/Decals (G6060 & PB6000
Only).....31
Cotter Pin, Stainless Steel Hair Pin.....29
Coupler, Conveyor Motor (G6060 & PB6000
Only).....31
Coupler, Quik, 3/4-16 ORB Female.....81
Coupler, Quik, Male, -08 ORB.....81
Coupling, Cable Drum.....7, 9
Coupling, Cable Rewind.....67
Cover, Cable Drum.....41
Cover, Drive Chain.....25
Cradle, Bag Boom, 10` - G6070 & G6070P
Only.....11
Cradle, Bag Boom, 8` & 9` - G6060 & PB6000
Only.....11
Cradle, Bag Boom, 9` - G6070 & G6070P
Only.....11
Cross & Bearing Kit.....65
Cross Kit, #8, 35 x 106.....63
Cup, Bearing, Inner.....13
Cup, Bearing, Outer.....13
Cylinder, Hydraulic, 2 in. x 28 in. x 1-1/8
in......39
Cylinder, Hydraulic, 3 x 18 in......81
D
Danger Label, Outer Drive Tube.....63
Danger/Shield Label.....63
Decal, 75W-90 Syn Oil.....53
Decal, Ag-Bag Logo, 7 x 19 in......53
Decal, ag-bag.com, 1.75 x 20 in......53
Decal, Ag-Bagger, 4 x 42 in......53
Decal, Conveyor End Lift.....81
Decal, Conveyor Raise/Lower.....39
Decal, Conveyor/Cable Rewind.....53
Decal, G6060 (G6060).....53
Decal, G6070 (G6070 & G6070P).....53
Decal, Grease.....53
Decal, Grease Rotor Bearing.....53
Decal, Hitch End Lift.....81
Decal, Important, Cable Guide Removal.....53
Decal, Important, Lug Nuts.....53
Decal, Inner.....65
Decal, Notice, Hydraulic Oil Only.....53
Decal, Notice, Tractor Neutral.....53
Decal, Oil Chain.....53
Decal, Outer.....65
Decal, Pinch Point.....81
Decal, Red Retroreflective 2 x 9 in......51
Decal, Red Retroreflective, 2 x 9 in......53
Decal, SMV Emblem.....53
Decal, Yellow Retroreflective 2 x 9 in......51
Decal, Yellow Retroreflective, 2 x 9 in......53
Deflector Weldment, Adjustment End.....29
Deflector, 2 Stage Conveyor G6070 &
G6070P.....22
Deflector, 2 Stage Conveyor w/Decal.....25
Deflector, 2 Stage Conveyor w/Decals
G6060.....22
Door Assembly, Conveyor with Hooks.....32
Drum, Cable, w/Brake Flange.....9
Drum, Cable, w/Brake Flange, 7 Ft Rotor.....7
Dust Cap, 1/2 in......81
Dust Plug, 1/2 in......81
E
Elbow, -08 ORB x 1/2 in. Male JIC.....81
Elbow, -12 ORB x -08 Male JIC.....81
Elbow, 1/2 in. NPT x 1/2 in. Male JIC.....81
Elbow, 1/2 MPT x 3/4 MJIC.....67
Elbow, 45° Street, #4 MP x #4 FP.....41
Elbow, 90° #6 ORB x #6 NPT.....39
Elbow, 90° 10 MJIC x FJIC.....39
Elbow, 90° 10 ORB x 6 MJIC.....39
Elbow, 90° 37° Flare, 3/4.....68
Elbow, 90°, 1/2 in. JIC Swivel.....81
F
Filter, Hydraulic, P551553.....67
Fitting, Grease (G6060 & PB6000 Only).....31
Fitting, Grease, 1/8 PTF.....26
Fitting, grease, 1/8 PTF.....21
Fitting, Grease, 1/8-PTF.....29
Fitting, Hose End Swivel (Use With Grease
Lines).....32
Flexible Roll Pin, #8/9 Inner, 12 x 75mm.....63
Flexible Roll Pin, #8/9 Outer, 12 x 90mm....63
Frame Weldment.....7, 9
Frame, Bag Boom, 8-10 Ft......45
Frame, Conveyor Slide.....35
G
Gandy, 45# 4H Dry Inoculant Applicator.....83
Gasket, Bearing Retainer, Gandy.....79
Gasket, Pump Flange.....67
Gasket, Top Access Plate.....67
Gauge, Liquid Fill, 2000 psi.....41
Gear.....55
Gear Box, Dual Output.....71
Gear, 700 Series.....57
Gearbox Complete.....57
Gearbox Complete, Viton Rebuilt.....57
Gearbox, Complete.....55
Gearbox, Dual Output Aluminum.....7
Gearbox, Dual Output Cast Iron.....7
Gearbox, Dual Output Cast Iron Viton
Rebuilt.....7
Grease Fitting, 1/4-28.....81
Grease Fitting, M6 x 1 Straight (Not Serviced
Separately).....63
Grease Line - 3/16 in. x 20.5 in. (Used On
G6070 Only).....32
Grease Line - 3/16 in. x 40 in. (Used On G6060
& PB6000 Only).....32
Grease Zerk, 1/8 in. NPT Female.....21
Grease Zerk, 1/8 NPT Female.....26
Guard Cone, 6 Rib Flex.....65
Guard Cone, 7 Rib.....65
Guard Tube, Inner.....65
Guard Tube, Outer.....65
Guard, Conveyor Idle Shaft.....22
Guard, Conveyor Tail Shaft (G6060 & PB6000
Only).....31
Guard, Rotor Chain - G6060 & PB6000
Only.....17
Guard, Rotor Chain - G6070 Only.....17
Guide, Cable Rewind, Left.....43
Guide, Cable Rewind, Right.....43
Guide, Chain Conveyor - Left (G6060 &
PB6000 Only) Not Shown.....32
Guide, Chain Conveyor - Right (G6060 &
PB6000 Only) Not Shown.....32
Guide, Conveyor Chain, Top LH.....21
Guide, Conveyor Chain, Top RH.....21
H
Half Shaft, Cleared (Not Serviced
Separately).....63
Half Shaft, Uncleared (Not Serviced
Separately).....63
Half Shield Kit (Not Serviced Separately)....63
Handle Kit.....67
Harness, Lights (Includes Item 28).....51
Harness, Lights, Wishbone.....51
Hhdnut - Lock 1/4 Whiz.....85
Hinge, Beater Shield.....22, 25
Hitch, Field, 10 Ft - G6070 & G6070P.....7
Hold Down, Conveyor.....35
42.0901805A Issue Date: 10/11 - 90 - G6070/G6070P
Part Description Index
(continued)