Altec Lansing Octiv AIR A11964 R07 - Manual (Page 8)

8
Advanced Operation
Multi-Speaker Systems
With a single transmitter base, you can transmit audio
to as many as eight wireless speakers. Speakers can be
set to standard stereo mode or to serve as pairs of left
and right speakers. By adding speakers to your system,
you can create separate listening areas served by one or
more speakers.
When you power up a multi-speaker system, turn on
the speakers first and then turn on the power to the
transmitter base. This will allow synchronization between
the speakers and the base. If one or more speakers fail
to synchronize or synchronization is lost during operation,
you must re-synchronize the system.
To re-synchronize the transmitter base with the
speaker(s), press and hold the STANDBY key on the
transmitter base. After three seconds, the LED to the
left of the STANDBY key will begin to flash. Continue to
hold down the STANDBY key until the LED stops flashing
(about six seconds).
Settings Menu
The settings menu of the M812 allows you to adjust
setup functions, such as RF channel, and audio
functions, such as bass and treble. The menu on the
M812 contains the following items:
BASS
TREBLE
FM MOdE
• US
• JAPAN
• EUROPE
Menu Navigation
Follow these steps to make changes to the settings:
1. Press and hold the INPUT key on the side panel of
the wireless speaker to enter the menu (about three
seconds).
2. To scroll through the menu use the VOLUME +/– keys
3. To select a menu item press the INPUT key.
4. To change the setting of a menu item scroll up or
down with the VOLUME +/– key.
5. When you finish making an adjustment, the menu
operation exits and returns to the previous operation.
You can also exit by selecting EXIT on the menu.
detailed Menu Operations
Set BASS and TREBLE
This menu option lets you adjust bass or treble.
1. Select BASS or TREBLE from the menu.
2. Press the VOLUME +/– key to scroll through tone
values from -6 to +6.
3. Press INPUT to select a value. The value is saved. The
display exits the menu.
Set FM MOdE
Three FM modes are included to accommodate radio
frequencies in different countries. Follow the steps below
to set the M812 for your region.
NOTE: When you change FM MODE, station presets are
erased.
1. Select FM MODE from the menu.
2. Press the VOLUME +/– key to scroll through the
possible values – US, JAPAN or EUROPE.
3. Press INPUT to select a value. The value is saved and
the display exits the menu.
Set RF Channels
This option allows you to adjust the radio frequency (RF)
channel settings to eliminate interference from other
nearby wireless devices, including other M812s. The
AUTO setting allows the M812 to use the clearest of the
three available channels. Or you may manually select
channel 1, 2 or 3.
1. Select RF CHAN from the menu.
2. Press the VOLUME +/– key to scroll through the
possible values – CH1, CH2, CH3 or AUTO.
3. Press INPUT to select one of the three channels or
select AUTO.
NOTES
• When using more than one speaker, ensure that all
speakers are on the same channel prior to setting the
transmitter.
• When you change the channel setting on the
speaker(s), you must also select the same channel on
the transmitter to keep sync. To do this:
1. Press and hold the STANDBY key on the base
transmitter for three seconds. The standby LED (on
the left) will blink. The SYNC1 and SYNC2 LEDs
indicate the current channel setting.
• LED1 illuminated – CH1 is selected (LED 2 is off.)
• LED2 illuminated – CH2 is selected (LED1 is off.)
• LED1 and LED2 illuminated – CH3 is selected
(Both LED 1 and LED2 are on.)
• No LEDs illuminated – AUTO is selected
2. Press the STANDBY key to change the RF channel.
3. Press and hold STANDBY for three seconds to save
your changes.
RF ChAN
• AUTO
• CH1
• CH2
• CH3
dEFAULT
• LOCAL
• FACTORY
EXIT