American Standard Town Square T555740 - Manual (Page 3)

M962636-YYY0A
VOLUME CONTROL HANDLE
T555740 TOWNSQUARE
TOWNSQUARE
Installation
Instructions
M 9 6 8 6 5 9
M 9 6 8 6 5 9 M 9 6 8 6 5 9 M 9 6 8 6 5 9
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
ASSE 1016
ROUGHING-IN DIMENSIONS
MODEL NUMBER
CHROME
BLACKENED BRONZE (PVD)
SATIN NICKEL (PVD)
002
068
295
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
Recommended Tools
Flat Blade Screwdriver Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
A907090-YYY0A
CAP
1
Remove PLASTER GUARD (1) if attached.
Push CAPS (2 & 2a) as shown onto CONTROL
VALVES (3).
Push ESCUTCHEON (4) over CAPS (2, 2a) and
flush against finished wall. Attach with the two
SCREWS (5) provided.
4
4
4
TEMPERATURE ADJUSTMENT
SET HOT LIMIT STOP
Check that arrow marking B points to the 3 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to
the right, pull off KNOB MOUNT (4) and reinstall KNOB MOUNT (4) with arrow "B" 3 o'clock position. See Figure 1.
For 100˚F adjustment, turn the water supply on. Turn KNOB MOUNT (4) until the spout temperature is 100˚F. Check
that arrow "A" on the KNOB MOUNT (4) still points 3 o'clock position after adjusting the thermostat to 100˚F.
If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT (4) by pulling it towards you while standing directly in
front of the valve.
Reinstall the KNOB MOUNT (4) with arrow "A" 3 o'clock position.
The maximum mixed water temperature is set at 109˚F at the factory. This setting can be changed if desired.
Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in
the diagram to limit the maximum mixed water temperature to 104˚F or 112˚F.
Reinstall RED LOCKING DEVICE.
See step 3 for HANDLE (3) installation.
Pull out index CAP (1) and remove HANDLE SCREW (2). Pull off HANDLE ASSEMBLY (3).
ARROW
"A"
BLACK
CLAMP
ARROW
"B"
RED LOCKING
DEVICE
TEMPERATURE
LIMIT STOP
ARROWS AT 3 O'CLOCK
POSITION
Figure 1
KNOB MOUNT
112
109
104
1
TRIM INSTALLATION
2
INSTALL HANDLES
Should the hot and cold water supply pipes have been transposed making
adjustment impossible, proceed as follows:
TRANSPOSED SUPPLY PIPING
OR BACK TO BACK INSTALLATION
3
Remove check stops and re-install them transposed.
Shut off water supply.
Remove handle and rim. (Reverse steps 1 and 2.
CHECK STOP
(RED TO BLUE)
Turn the water supply back on and perform the temperature adjustment in step 4.
Assemble HANDLES and TRIM.
CHECK STOP
(BLUE TO RED)
Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE
CHECK STOP is now on the left.
CENTRAL THERMOSTAT
WITH VOLUME CONTROL
TRIM KIT
1
8
1
5
9
10
11
3
4
6
2
2a
3
TOP
1
5
7
Align HANDLE BASE (1) and push onto KNOB MOUNT (2).
Install LEVER HANDLE (3) as shown. Install HANDLE SCREW (4) and
tighten with screwdriver.
Push INDEX CAP (5) into HANDLE (3).
Install HANDLE ADAPTER (6) onto VALVE STEM (7).
Install HANDLE SCREW (8) and tighten.
Push VOLUME CONTROL KNOB (9) onto HANDLE ADAPTER (6).
Use HEX WRENCH (10) supplied and tighten set screw to secure
VOLUME CONTROL KNOB (9).
Push in PLUG BUTTON (11).
2
M962635-YYY0A
ESCUTCHEON AND SCREWS
A918434-YYY0A
ESCUTCHEON SCREWS
M962633-YYY0A
HANDLE SCREW
AND INDEX BUTTON
M908587-YYY0A
HANDLE BASE
M916815-YYY0A
LEVER HANDLE
© AS America, Inc. 2007
CENTRAL THERMOSTAT
WITH VOLUME CONTROL
TRIM KIT
186mm
(7-3/8)
100mm
(3-7/8)
230mm
(9)
230mm
(9)
48mm to 68mm
(2 to 2-5/8)
150mm
(6)
NOTE: FITTING
MUST BE INSTALLED
WITH VOLUME CONTROL
ON TOP.
R520
1/2" NPT INLETS
or
R540
3/4" NPT INLETS
25mm
(1)
FINISHED
WALL
190mm
(7-1/2)
4
2
3
T555740