Electrolux EN18WI30LS - Manual (Page 12)

10
7.
Installation
Securing to the wall
Illustration
$IFDL
%SJMMIPMFTGPSUIFSFNBJOJOHGPVSTDSFXT
)BOHUIFVOJUBHBJOCZUIFàSTUTDSFX
BOEUIFO
insert and tighten the remaining four screws.
5BLFXBUFSQSPPàOHNFBTVSFTTPUIBUXBUFSEPFT
not enter the building from screws mounting the
device.
r.BLFTVSFUIFVOJUJTJOTUBMMFETFDVSFMZTPUIBUJUXJMM
OPUGBMMPSNPWFEVFUPWJCSBUJPOTPSFBSUIRVBLFT
%SJMMBTJOHMFTDSFXIPMF
NBLJOHTVSFUPIJUBTUVE
*OTFSUBOEUJHIUFOUIFTDSFXBOEIBOHUIFVOJUCZ
UIFVQQFSXBMMNPVOUJOHCSBDLFU
3. Determine the positions for the remaining four screws
UXPGPSUIFUPQCSBDLFUBOEUXPGPSUIFCPUUPN
BOE
remove the unit.
r5IFXFJHIUPGUIFEFWJDFXJMMCFBQQMJFEUPUIFXBMM*GUIFTUSFOHUIPGUIFXBMMJTOPUTVGàDJFOU
reinforcement must be done to prevent the transfer of vibration.
r%POPUESPQPSBQQMZVOOFDFTTBSZGPSDFUPUIFEFWJDFXIFOJOTUBMMJOH*OUFSOBMQBSUTNBZ
be damaged and may become highly dangerous.
r*OTUBMMUIFVOJUPOBWFSUJDBMXBMMBOEFOTVSFUIBUJUJTMFWFM
-PDBUJOH
4DS
FX
)PMFT
.PVOUJOH
Structur
e
r8IFOJOTUBMMJOHXJUICBSFIBOET
UBLFDBVUJPOUP
not inflict injury.
r#FDBSFGVMOPUUPIJUFMFDUSJDBMXJSJOH
HBT
PSXBUFS
piping while drilling holes.
Item
CAUTION
Be sure to do
.PVOUJOH#SBDLFU
(upper)
-PDBUJPOPG4DSFX)PMF
-PDBUJOH4DSFX)PMFT
Installations at Elevations
"CPWF
GU
r"EKVTUUIFEJQTXJUDIFTBTJMMVTUSBUFEJOUIFUBCMFUP
the right if this water heater is installed at an altitude
PGGU NPSIJHIFS
r%JTDPOOFDUQPXFSUPUIFXBUFSIFBUFSCFGPSFDIBOHJOH
UIFEJQTXJUDIFT'BJMVSFUPQFSGPSNUIJTTUFQXJMMSFTVMU
JO B DPEF EJTQMBZFE PO UIF SFNPUF DPOUSPMMFS
and a cease in operation. If this occurs, disconnect,
then reconnect power to the water heater to reset
the system.
Note : Please refer to page 31 for the location of the
EJQTXJUDICBOL
Anchoring Screw
* Do not change any other dipswitches.
* High elevation adjustment.
6 5
2,001 - 4,000 ft (611 - 1,220m)
0 - 2,000 ft (0 - 610m)
ON= OFF=
4,001 - 6,000 ft (1,221 - 1,830m)
6,001 - 8,000 ft (1,831 - 2,440m)