TOHO ELECTRONICS TTM200 - Manual (Page 40)

40
Control setting mode (set4)
toho modbus
Screen
character
Name Command Remark
Identifier
Absolute
(DEC)
Relative (hex)
BNK 41025 0400 bANK Switch to another bank RWLB
BKH 41139 0472 bANKH Bank upper limit setting RWLB
Pay attention to MODBUS
address.
SV1 41027 0402 SV Control set RWLB
SLH 41029 0404 SLH SV limiter upper limit RWLB
SLL 41031 0406 SLL SV limiter lower limit RWLB
□MD 41033 0408 Md Control mode RWLB
00000:RUN
00001:MAN
00002:RdY
00003:TIME1
00004:TIME2
00005:TIME3
CNT 41035 040A CNt Set a control type RWLB
TYP 41037 040C tYP Set a PID control type RWLB
BMD 41039 040E bMd Set type B mode RWLB
DIR 41041 0410 dIR Set a forward/backward action RWLB
MV1 41043 0412 MV1 Main control operation amount RWLB
M1G 41045 0414 MV1G Set an output gain RWLB
TUN 41047 0416 tUN Set a tuning type RWLB
ATG 41049 0418 AtG Set an AT factor RWLB
ATC 41051 041A AtC Set an AT sensitivity RWLB
□AT 41053 041C At Start/stop tuning RWLB
00000: Stop
00001: Start
□P1 41055 041E P1 Set a main control proportional band RWLB
□I1 41057 0420 I Set an integration time RWLB
□D1 41059 0422 d Set a derivative time RWLB
□T1 41061 0424 t1 Set a main control proportional period RWLB
ARW 41063 0426 ARW Anti-reset windup RWLB
MH1 41065 0428 MLH1
Main control operation amount limiter, upper
limit
RWLB
ML1 41067 042A MLL1
Main control operation amount limiter, lower
limit
RWLB
OU1 41069 042C oU1 Set a main control change limiter rise RWLB
OD1 41071 042E od1 Set a main control change limiter decline RWLB
SFM 41119 045E SFM Set a main control soft-start output RWLB
Pay attention to MODBUS
address.
SFT 41121 0460 SFt Set a main control soft-start time RWLB
Pay attention to MODBUS
address.
FA1 41073 0430 FAL1 Set a main control anomaly RWLB
1TS 41127 0466 tS1
Set a main control loop anomaly PV
threshold
RWLB
Pay attention to MODBUS
address.
1MS 41129 0468 MS1
Set a main control loop anomaly MV
threshold
RWLB
Pay attention to MODBUS
address.
1PS 41131 046A PS1
Set a main control loop anomaly PV change
threshold
RWLB
Pay attention to MODBUS
address.
LP1 41075 0432 LoP1 Set a main control loop anomaly time RWLB
CMD 41077 0434 CMod Set an OFF point position selection RWLB
□C1 41079 0436 C1 Set a main control sensitivity RWLB
CP1 41081 0438 CP1 Set an OFF point position RWLB
FD1 41123 0462 Fdt1 Main control protection off timer RWLB
Pay attention to MODBUS
address.
ND1 41141 0474 Ndt1 Main control protection on timer RWLB
Pay attention to MODBUS
address.
MV2 41083 043A MV2 Auxiliary control operation amount RWLB
M2G 41085 043C MV2G Set an auxiliary control output gain RWLB
□P2 41087 043E P2 Set an auxiliary control proportional band RWLB
□T2 41089 0440 t2 Set an auxiliary control proportional period RWLB
MH2 41091 0442 MLH2
Auxiliary control operation amount limiter,
upper limit
RWLB
ML2 41093 0444 MLL2
Auxiliary control operation amount limiter,
lower limit
RWLB
OU2 41095 0446 oU2 Set an auxiliary control change limiter rise RWLB
OD2 41097 0448 od2
Set an auxiliary control change limiter
decline
RWLB