PATLITE VE100-304SU - Manual (Page 2)

㻞䠊㻯㼛㼚㼠㼑㼚㼠㼟
㻡䠊㻯㼛㼚㼚㼑㼏㼠㼕㼛㼚
㻡㻚㻝䚷㻭㻯㻌㻭㼐㼍㼜㼠㼛㼞㻌㻯㼛㼚㼚㼑㼏㼠㼕㼛㼚
䞉 Refer to the following figure for connecting the AC Adaptor .
㻟䠊㻼㼍㼞㼠㻌㻺㼍㼙㼑㼟㻌㼍㼚㼐㻌㼠㼔㼑㼕㼞㻌㻲㼡㼚㼏㼠㼕㼛㼚
㻠䠊㻼㼞㼛㼐㼡㼏㼠㻌㻿㼜㼑㼏㼕㼒㼕㼏㼍㼠㼕㼛㼚
[VE25]
㻡㻚㻞䚷㻲㻳㻌㼃㼕㼞㼕㼚㼓
[VE25] [VE100]
㻌
䖃 Do not locate near high temperature sources, open flames or humid places.
Moreover, do not use this machine in a place which can be exposed to corrosive or
combustible gas.
䖃 Avoid the intrusion of foreign substances, such as water or chemicals; or metals, such
as metal filings, from entering this machine. Failure to comply may result in product
failure or electric shock.
䖃 Do not attempt to repair or modify this machine. Failure to comply will result in
equipment damage or fire.
䖃 Please do not over-bend the AC Adaptor cable. Disconnection will result in this
machine breaking down.
Caution
2. Insert the AC Adaptor
plug into the jack.
4. Fix the AC Adaptor cable
with the clamp.
㼇㼂㻱㻝㻜㻜㼉
1. Remove two M4×45
screws and the cover
3. Push the AC Adaptor
cable into the slot.
䞉 Connect the FG line to a ground to improve noise resistance, prevent electric shock, and
protect from lightning strikes, etc.The connection should be made to the Terminal Buss.
䞉 The FG line should be connected to a solid ground at any cost. If the FG line is connected
to other equipment or is connected to a building beam, it may cause an adverse effect, and
even increase the reception of noise, etc.
䞉 The wire for the FG line should be a multi-core cable with a nominal cross-sectional area of
0.75mm2 or more.
[VE25]
[VE100]
70
205 95 95
68 139.5
19
178
580
480
60
74 27
8.2
ij
40
270
16
200
70 10
68 61.5
43
19
The following contents are contained in this product. Please check off the following items when
removing it from the package.
䞉 Model 䠲䠡 Main Unit
䞉 Instruction Manual (this document䠅
䞉 Exclusive AC Adaptor
䞉 AC Adaptor Cable
䈜 The optional infra-red remote control (Model VE-IRU) is required when using this machine.
However, we recommend you purchase it separately.
1. Remove two M4×45
screws and the cover
2. Insert the AC Adaptor
plug into the jack.
4. Fix the AC Adaptor cable
with the clamp.
3. Push the AC Adaptor
cable into the slot.
No. Name Function
① Display
Displays the numerical values. Character size for the VE25 is 25mm (1 in.)
and the VE100 is 100mm (4 in.).
② Infrared Sensor Infrared input for the optional infrared remote control (VE-IRU Sold Separately).
③ Mounting Bracket Hardware used for mounting the display unit to a wall, etc.
④ Mounting Holes
Holes available for mounting the display with optional brackets and M6 screws
(Sold separately, Maximum length: 25mm).
⑤ Terminal Bus All signal and communication connections are wired here.
⑥ DC Jack For connecting the VE Series AC Adaptor to the unit.
⑦ Clamp Used to secure the AC Adaptor cable.
⑧ Power Input Runs the cable for the AC Adaptor through the panel.
⑨ Terminating Resistor
Switch
Used to switch the internal impedance "ON" or "OFF" for the RS-485
transmission terminal inputs.
㻠㻚㻞䚷㻼㼑㼞㼒㼛㼞㼙㼍㼚㼏㼑㻌㻿㼜㼑㼏㼕㼒㼕㼏㼍㼠㼕㼛㼚㼟
Model Name VE25-304SU VE100-304SU
Display Characters Numbers, Minus, Decimal Point, Symbols
Character Height 25mm (1 in.) 100mm (4 in.)
Element Type Segment LED Element Round-shaped LED Element
Color Red
Tiers/Digits 3 Tiers with 4 place digits
Operating Mode Numerical Display/Production Control Mode
LED Brightness Setting 3 Settings of High, Middle and Low; Off and On.
Input Terminals
6 Input Terminal Buss
No-voltage contact current (photocoupler insulation) and short-circuit current of about 10mA with an
internal DC voltage of 12V.
Output Terminals 3 Output Terminal Buss (“ACHIEVE”, “GAIN +”, “LOSS -”)
NPN Open Collector; maximum load DC24V, 100mA, residual voltage drop of about 1V
Power Supply Exclusive AC Adaptor Included
Setting Method Infrared Remote Control (Remote Control VE-IRU type sold as an option).
Memory Retention Period: About one month with a full charge*
Clock Accuracy ±5 seconds or less (at 25 o C)
Communication
Function
RS-485 Standard Transmission System: Half-duplex, synchronized system; Start-stop synchronization
Terminating Resistor Switch: ON/OFF is set from the switch located on the back-panel.
Maximum Host Connection of 32 units; ID: 01- 32 (Sets up via remote control)
Baud rate: 4800 bps, 9600bps, 19200bps, 38400bps (Sets up via remote control)
Stop bit: 2 bits; Data Length: 8 bits; Parity: Even, Odd, None
䈜 The battery has to be cycled to a full charge for memory storage retention to last about 24 hrs. (at 25 o C)
Item Speci¿ cation
Rated Voltage AC100 - 240V (50Hz/60Hz) *1 12VDC *4
Voltage Range AC90 to 264V *1
Operating Temperature Range 0 o C to 40 o C
Relative Humidity 35 to 85% RH (No dew or condensation)
Storage Temperature Range -10 o C to 70 o C
Mounting Location Indoors Only
Insulation Resistance More than 1Mohm at 500VDC between the AC Adaptor power supply and the Frame Ground. *1
Withstand Voltage 1500VAC applied for 1 minute between the AC Adaptor power supply and Frame Ground without
breaking insulation. (Detected Current: 10mA) *1
Vibration Resistance JIS C0040 Acceleration 19.6m/s 2
Noise Resistance
(Power Supply)
9SS QVȝV SXOVHV *1
Outside Dimensions VE25-304SU : 270(W) × 200(L) × 70(D) mm *2
VE100-304SU : 580(W) ×480(L) ×70(D) mm
Mass *3 VE25-304SU : 2.5kg or less
VE100-304SU : 6.5kg or less
Maximum Power Consumption VE25-304SU : 11W *1
VE100-304SU : 12W *1
Conformity Standards
FCC Part 15 Subpart B Class A
Compliant to RoHS Directive (DIRECTIVE 2002/95/EC)
㻠㻚㻝䚷㻳㼑㼚㼑㼞㼍㼘㻌㻿㼜㼑㼏㼕㼒㼕㼏㼍㼠㼕㼛㼚㼟
䈜㻌㻌 The above contents may change without preliminary notice for product improvements, etc.
䈜1 Value when using the AC adaptor accessory.
䈜2 The Installation Bracket dimensions are not included.
䈜3 Mass with the AC adaptor included.
䈜4 Main Unit Only.
Caution Be sure to disconnect the power prior to wiring.
Failure to comply may result in product failure or electric shock.